Register July 2006 No. 607

Chapter NR 664

APPENDIX IV

COCHRAN'S APPROXIMATION TO THE BEHRENS-FISHER STUDENTS' T-TEST

Using all the available background data (nb readings), calculate the background mean (Xb) and background variance (sb2). For the single monitoring well under investigation (nm reading), calculate the monitoring mean (Xm) and monitoring variance (sm2).

For any set of data (X1, X2, . . ., Xn) the mean is calculated by:

and the variance is calculated by:

where “n" denotes the number of observations in the set of data.

The t-test uses these data summary measures to calculate a t-statistic (t*) and a comparison t-statistic (tc). The t* value is compared to the tc value and a conclusion reached as to whether there has been a statistically significant change in any indicator parameter.

The t-statistic for all parameters except pH and similar monitoring parameters is:

If the value of this t-statistic is negative then there is no significant difference between the monitoring data and background data. It should be noted that significantly small negative values may be indicative of a failure of the assumption made for test validity or errors have been made in collecting the background data.

The t-statistic (tc), against which t* will be compared, necessitates finding tb and tm from standard (one-tailed) tables where,

tb=t-tables with (nb-1) degrees of freedom, at the 0.05 level of significance.

tm=t-tables with (nm-1) degrees of freedom, at the 0.05 level of significance.

Finally, the special weightings Wb and Wm are defined as:

and so the comparison t-statistic is:

The t-statistic (t*) is now compared with the comparison t-statistic (tc) using the following decision-rule:

If t* is equal to or larger than tc, then conclude that there most likely has been a significant increase in this specific parameter.

If t* is less than tc, then conclude that most likely there has not been a change in this specific parameter.

The t-statistic for testing pH and similar monitoring parameters is constructed in the same manner as previously described except the negative sign (if any) is discarded and the caveat concerning the negative value is ignored. The standard ( 2-tailed) tables are used in the construction tc for pH and similar monitoring parameters.

If t* is equal to or larger than tc, then conclude that there most likely has been a significant increase (if the initial t* had been negative, this would imply a significant decrease). If t* is less than tc, then conclude that there most likely has been no change.

A further discussion of the test may be found in Statistical Methods (6th Edition, Section 4.14) by G. W. Snedecor and W. G. Cochran, or Principles and Procedures of Statistics (1st Edition, Section 5.8) by R. G. D. Steel and J. H. Torrie.

Adopted from Table III of “Statistical Tables for Biological, Agricultural, and Medical Research" (1947, R. A. Fisher and F. Yates).

/code/admin_code/nr/600/664_iv
true
administrativecode
/code/admin_code/nr/600/664_iv/_1
Department of Natural Resources (NR)
Chs. NR 600-699; Environmental Protection – Hazardous Waste Management
section
true

×
Details for

PDF view

Link (Permanent link)

Bookmark this location

View toggle

Go to top of document

Search in this chapter

Search in this section

Search in this agency

Search in this chapter group

Search in this chapter

Search in this section

Cross references for section

Acts affecting this section

References to this

1970 Statutes Annotations

Appellate Court Citations

Administrative Code Index

Reference lines

Clear highlighting

PDF view

Link (Permanent link)

Bookmark this location

View toggle

Go to top of document

Search in this chapter

Search in this section

Search in this agency

Search in this chapter group

Search in this chapter

Search in this section

Cross references for section

Acts affecting this section

References to this

1970 Statutes Annotations

Appellate Court Citations

Administrative Code Index

Reference lines

Clear highlighting

Published under s. 35.93, Stats. Updated on the first day of each month. Entire code is always current. The Register date on each page is the date the chapter was last published.