347.36 History
History: 1983 a. 243.
347.37
347.37
Brake fluid, sale regulation. 347.37(1)
(1) After January 1, 1960, no hydraulic brake fluid for use in motor vehicles shall be sold in this state if such brake fluid is below the minimum standard of specifications established by the society of automotive engineers for heavy duty type brake fluid No. 70R1 or a later designator for an improved product.
347.37(2)
(2) All manufacturers of brake fluids selling such fluids in Wisconsin shall state on the immediate containers in which such fluid is packaged that the fluid therein meets or exceeds the specifications under
sub. (1).
347.38
347.38
Horns and warning devices. 347.38(1)
(1) No person shall operate a motor vehicle upon a highway unless such motor vehicle is equipped with a horn in good working order and capable of emitting sound audible under normal conditions from a distance of not less than 200 feet, but no person shall at any time use a horn otherwise than as a reasonable warning or make any unnecessary or unreasonably loud or harsh sound by means of a horn or other warning device.
347.38(2)
(2) Except as otherwise provided in this section, no vehicle shall be equipped with nor shall any person use upon a vehicle any siren or compression or exhaust whistle.
347.38(3)
(3) Any vehicle may be equipped with a theft alarm signal device if such device is so arranged that it cannot be used by the driver as an ordinary warning signal.
347.38(4)
(4) An authorized emergency vehicle shall be equipped with a siren, but such siren shall not be used except when such vehicle is operated in response to an emergency call or in the immediate pursuit of an actual or suspected violator of the law, in which events the driver of such vehicle shall sound the siren when reasonably necessary to warn pedestrians and other drivers.
347.39(1)(1) No person shall operate on a highway any motor vehicle subject to registration unless such motor vehicle is equipped with an adequate muffler in constant operation and properly maintained to prevent any excessive or unusual noise or annoying smoke. This subsection also applies to motor bicycles.
347.39(2)
(2) No muffler or exhaust system on any vehicle mentioned in
sub. (1) shall be equipped with a cutout, bypass or similar device nor shall there be installed in the exhaust system of any such vehicle any device to ignite exhaust gases so as to produce flame within or without the exhaust system. No person shall modify the exhaust system of any such motor vehicle in a manner which will amplify or increase the noise emitted by the motor of such vehicle above that emitted by the muffler originally installed on the vehicle, and such original muffler shall comply with all the requirements of this section.
347.39(3)
(3) In this section, "muffler" means a device consisting of a series of chambers of baffle plates or other mechanical design for receiving exhaust gases from an internal combustion engine and which is effective in reducing noise.
347.39 History
History: 1983 a. 243.
347.40(1)(1) No person shall operate any motor vehicle upon a highway unless such vehicle is equipped with a mirror so located as to reflect to the operator a view of the roadway for a distance of 200 feet to the rear of such vehicle.
347.40(2)
(2) No person shall operate on a highway any school bus having a passenger-carrying capacity of 10 or more persons including the operator unless such bus is equipped with at least one mirror which is 7 inches in diameter so located as to enable the operator to see a reflection of the road from the entire front bumper forward to a point where direct observation is possible.
347.40(3)
(3) No person may operate or permit the operation of any motor bus on a highway unless the bus is equipped with 2 outside rearview mirrors, one to the right and one to the left of the operator. Each mirror shall have not less than 50 square inches of unobstructed reflective surface and shall be firmly supported and adjustable to give the operator a clear view past both the right and left rear of the bus.
347.40 History
History: 1975 c. 84;
1987 a. 235.
347.41
347.41
Speed indicators. No person shall operate on a highway any motor vehicle primarily designed for use upon a highway unless such motor vehicle is equipped with a speedometer which with reasonable accuracy registers the speed of the vehicle, except that motor trucks or truck tractors may be equipped with tachometers or any other devices that indicate speed and motor vehicles transported pursuant and in compliance with
s. 341.47 (1) (b) and
(c) may be equipped with a governor of speed of a type which restricts speed and which is set at a level equal to or below the limits of 55 miles per hour in lieu of a speedometer.
347.41 History
History: 1983 a. 54.
347.413
347.413
Ignition interlock device tampering. 347.413(1)
(1) No person may remove, disconnect, tamper with or otherwise circumvent the operation of an ignition interlock device installed in response to the court order under
s. 346.65 (6). This subsection does not apply to the removal of an ignition interlock device upon the expiration of the order requiring the motor vehicle to be so equipped or to necessary repairs to a malfunctioning ignition interlock device by a person authorized by the department.
Effective date note
NOTE: Sub. (1) is amended eff. 1-1-02 by
1999 Wis. Act 109 to read:
Effective date text
(1) No person may remove, disconnect, tamper with or otherwise circumvent the operation of an ignition interlock device installed in response to the court order under s. 346.65 (6), 1997 stats., or s. 343.301 (1). This subsection does not apply to the removal of an ignition interlock device upon the expiration of the order requiring the motor vehicle to be so equipped or to necessary repairs to a malfunctioning ignition interlock device by a person authorized by the department.
347.413(2)
(2) The department shall promulgate a rule establishing specifications and requirements for approved types of ignition interlock devices and their calibration, installation and maintenance.
347.413(3)
(3) The department shall design a warning label which shall be affixed to each ignition interlock device upon installation. The label shall provide notice of the penalties for tampering with or circumventing the operation of the ignition interlock device under
sub. (1) and
s. 343.10 (5) (a) 3.
347.415
347.415
Odometer tampering. 347.415(1)(1) No person shall, either personally or through an agent, remove, replace, disconnect, reset, tamper with, alter, or fail to connect the odometer of any motor vehicle with the intent to change or affect the number of miles indicated thereon.
347.415(2)
(2) No person may operate a motor vehicle subject to registration under
ch. 341 on any street or highway with knowledge that the odometer is removed, disconnected or nonfunctional. An exemption may be provided if parts are on back order to correct a nonfunctional odometer.
347.415(3)
(3) No person may advertise for sale, sell, use, install, or have installed any device which causes an odometer to register any mileage other than the true mileage driven. For purposes of this subsection, "true mileage driven" means that mileage traveled by the vehicle as measured and recorded by the odometer within the manufacturer's design tolerance.
347.415(5)
(5) Nothing in this section shall prevent the service, repair or replacement of an odometer, provided the mileage indicated thereon remains the same as before the service, repair or replacement. Where the odometer is incapable of registering the same mileage as before such service, repair or replacement, the odometer shall be adjusted to read zero, and a written notice shall be attached, by the owner or an agent, to the left door frame of the vehicle, or other location as prescribed by the department, specifying the mileage prior to service, repair or replacement of the odometer and the date on which it was serviced, repaired or replaced. No person may, with intent to defraud, remove or alter such a notice so affixed. No person who services, repairs or replaces an odometer that is incapable of registering the same mileage as before such service, repair or replacement may fail to adjust the odometer to read zero or fail to attach the notice required by this subsection.
347.417
347.417
Immobilization device tampering. 347.417(1)
(1) No person may remove, disconnect, tamper with or otherwise circumvent the operation of any immobilization device installed in response to a court order under
s. 346.65 (6). This subsection does not apply to the removal of an immobilization device pursuant to a court order or to necessary repairs to a malfunctioning immobilization device.
Effective date note
NOTE: Sub. (1) is amended eff. 1-1-02 by
1999 Wis. Act 109 to read:
Effective date text
(1) No person may remove, disconnect, tamper with or otherwise circumvent the operation of any immobilization device installed in response to a court order under s. 346.65 (6), 1997 stats., or s. 343.301 (2). This subsection does not apply to the removal of an immobilization device pursuant to a court order or to necessary repairs to a malfunctioning immobilization device.
347.417(2)
(2) The department shall design a warning label which shall be affixed by the owner of each immobilization device before the device is used to immobilize any motor vehicle under
s. 346.65 (6). The label shall provide notice of the penalties for removing, disconnecting, tampering with or otherwise circumventing the operation of the immobilization device.
Effective date note
NOTE: Sub. (2) is amended eff. 1-1-02 by
1999 Wis. Act 109 to read:
Effective date text
(2) The department shall design a warning label which shall be affixed by the owner of each immobilization device before the device is used to immobilize any motor vehicle under s. 343.301 (2). The label shall provide notice of the penalties for removing, disconnecting, tampering with or otherwise circumventing the operation of the immobilization device.
347.417 History
History: 1991 a. 277;
1999 a. 109.
347.42
347.42
Windshield wipers. No person may operate on a highway any motor vehicle equipped with a windshield, except a moped or Type 1 motorcycle, unless the motor vehicle also is equipped with a device for cleaning rain, snow or other moisture from the windshield. The device shall be so constructed as to be controlled or operated by the operator of the vehicle and shall at all times be maintained in good working order.
347.43(1g)(1g) In this section, "safety glass" means glass so treated or combined with other materials as to reduce, in comparison with ordinary sheet glass or plate glass, the likelihood of injury to persons by objects from external sources or by such glass when it is struck, cracked or broken.
347.43(1s)
(1s) No person may operate upon a highway any motor vehicle manufactured after January 1, 1936, unless the motor vehicle is equipped with safety glass wherever glass is used on the motor vehicle in partitions, doors, windows or windshields.
347.43(2)
(2) No person may sell any new motor vehicle unless such vehicle is equipped with safety glass in accordance with the requirements of
sub. (1s).
347.43(4)
(4) If a common carrier or person operating under a permit or certificate issued by the department is convicted of operating a vehicle in violation of this section, the department may suspend or revoke the permit or certificate until such time as the vehicle has been equipped with safety glass as required by this section.
347.44
347.44
Painting requirements for school buses; restrictions as to painting of other vehicles. 347.44(1)
(1) All school buses shall be painted as follows:
347.44(1)(a)
(a) With the exception of trim, the body, including hood, fenders, cowl and roof shall be painted a uniform color, national school bus glossy yellow, according to national institute of standards and technology specifications;
347.44(1)(b)
(b) The body trim, if used, shall be black; and
347.44(1)(c)
(c) The words, "SCHOOL BUS", in black letters at least 8 inches high shall appear on both the front and rear of the upper body area or on a sign attached thereto.
347.44(2)
(2) A motor vehicle described in
s. 340.01 (56) (b) may, but need not, comply with
sub. (1). If the motor vehicle complies with
sub. (1), the vehicle shall comply with other regulations relating to school buses prescribed by the department by rule.
347.44(3)
(3) No person may paint or in any way designate a motor vehicle in the manner described in
sub. (1) except as expressly authorized by this section.
347.44(4)
(4) When a motor vehicle in compliance with
sub. (1),
s. 347.25 (2), and the rules of the department relating to school bus equipment is no longer operated as a school bus, the registration of the motor vehicle for another purpose may not be permitted until the owner:
347.44(4)(a)
(a) Physically removes the signs identifying the vehicle as a school bus, the lights required by
s. 347.25 (2) and such other equipment as the department may specify by rule; and
347.44(4)(b)
(b) Repaints the entire vehicle to a color other than national school bus glossy yellow or any color commonly referred to as yellow.
347.45(1)(1) All automobiles, motor trucks, motor buses, truck tractors, trailers, semitrailers and mobile homes when operated upon a highway shall be completely equipped with tires inflated with compressed air and all other motor vehicles when operated on a highway shall be equipped with tires of rubber or of some material or construction of equal resiliency. No person may operate on a highway any motor vehicle, trailer, semitrailer or mobile home having any metal tire in contact with the roadway, except that tire chains of reasonable proportions may be used when required for safety because of snow, ice or other conditions tending to cause a vehicle to skid, and except as provided in
sub. (2) (c).
347.45(2)
(2) No person shall operate on a highway any vehicle, including farm tractors, self-propelled farm implements, implements of husbandry, animal-drawn vehicles and road machinery, if such vehicle has on the periphery of any of its tires any block, stud, flange, cleat, spike or other protuberance of any material other than rubber which projects beyond the tread of the traction surface of the tire, except that:
347.45(2)(a)
(a) Farm tractors, self-propelled farm implements, implements of husbandry, animal-drawn vehicles and road machinery may be operated with metal tires or tires having protuberances that will not injure the highway.
347.45(2)(b)
(b) Tire chains of reasonable proportions may be used on any vehicle when required for safety because of snow, ice or other conditions tending to cause a vehicle to skid.
347.45(2)(c)
(c) A pneumatic tire may have embedded in it wire or wire coils for improving traction on ice and snow, but such tire shall be so constructed that the per cent of wire or wire coils in contact with the roadway does not exceed, after the first 1,000 miles of use or operation, 5% of the total tire area in contact with the roadway. During the first 1,000 miles of use or operation of any such tire the wire or wire coils in contact with the roadway shall not exceed 20% of the total tire area in contact with the roadway. Tires equipped with tungsten carbide studs shall be limited in usage and design as follows:
347.45(2)(c)1.
1. The department shall, by rule, designate the times of year during which any type of tire described in this paragraph may be used.
347.45(2)(c)2.
2. Such tires may be used only on authorized emergency vehicles, school buses, vehicles used to deliver mail and automobiles with out-of-state registrations and then only if such automobile is in the course of passing through this state for a period of not more than 30 days.
347.45(2)(c)3.
3. Such studs shall not project more than one-eighth inch beyond the tread surface of the tire.
347.45(3)
(3) The authority in charge of maintenance of the highway in question may, in its discretion, issue a special permit authorizing operation upon such highway of a vehicle the operation of which would otherwise be prohibited under this section.
347.45(4)
(4) No person shall knowingly operate on any highway any vehicle on which any tire has been regrooved or recut or offer such tire for sale or exchange. This subsection shall not apply to regrooved or recut commercial vehicle tires which are designed and constructed in such a manner that regrooving or recutting is an acceptable and safe practice, nor does this subsection apply to regrooving or recutting done in a tire recapping process.
347.455
347.455
Modifications to height of vehicle. 347.455(1)
(1) Except as further provided in this section, no person may operate any vehicle on a highway if modifications have been made to the suspension system, axles or chassis of the vehicle which cause any portion of the vehicle to ride more than 4 inches above the height of the vehicle specified by the manufacturer. The height of the vehicle shall be measured from the level surface on which the vehicle stands.
347.455(2)
(2) If the modification is for the purpose of strengthening or improving handling, modifications may be made to the suspension system, axles or chassis of a 4-wheel drive vehicle or a motor truck which has a gross weight of not more than 8,000 pounds which cause the vehicle to ride 5 or less inches above the height of the vehicle specified by the manufacturer. The height of the vehicle shall be measured from the level surface on which the vehicle stands.
347.455(3)
(3) A 4-wheel drive vehicle or a motor truck which has a gross weight of not more than 8,000 pounds may be modified to use a tire and wheel size which exceeds the wheel and tire size specified by the manufacturer for the vehicle by up to 4 inches in radius.
347.455(4)
(4) No person may operate any vehicle on a highway if modifications have been made to the suspension system, axles, chassis or exhaust system of the vehicle which cause any portion of the vehicle, except the tires, to extend below lines drawn from the bottom of each wheel rim to the points of contact between the tires on the opposite side and opposite end of the vehicle and the level surface on which the vehicle stands.
347.455 History
History: 1981 c. 216;
1993 a. 165.
347.46
347.46
Fenders and mudguards. 347.46(1)
(1) No person shall operate a vehicle of the tractor type on a highway unless the driving wheels of such vehicle are protected by suitable fenders.
347.46(2)
(2) No person shall operate on a highway in intercity movement any privately owned motor truck or privately owned semitrailer drawn by a truck tractor, except those motor trucks and semitrailers equipped with dump bodies, unless such motor truck or semitrailer is equipped with rear fenders or mudguards of such material and so constructed and placed as to restrict to a minimum the splashing of water, mud or other material which may be thrown by the rear wheels. Such rear fenders or mudguards shall meet the following minimum specifications:
347.46(2)(a)
(a) The fenders or mudguards shall cover the tire or multiple tires they are protecting starting at the top from a line drawn vertically through the center of the axle and extending rearward and downward so that the fender or mudguard under any condition of operation or loading of the vehicle has a ground clearance of not more than one third of the horizontal distance from the center of the rearmost axle to the fender or mudguard;
347.46(2)(b)
(b) The fenders or mudguards shall be at least as wide as the tire or multiple tires they are protecting;
347.46(2)(c)
(c) If the vehicle is so designed and constructed that the rear wheels are covered in the manner specified in
pars. (a) and
(b) by means of fenders, body construction or other means of enclosure, then no special mudguards are required. Otherwise, the vehicle shall be equipped with special mudguards to the extent necessary to meet the requirements of
pars. (a) and
(b).
347.47
347.47
Drawbars, trailer hitches and mobile home couplings. 347.47(1)(1) No person shall operate a vehicle towing or drawing another vehicle or vehicles on a highway if the drawbar or other connection between any 2 vehicles exceeds 12 feet in length.
