SPS 366.0202(2)(a)(a) Substitute the following definition for the corresponding definition in IEBC section 202: "Historic building" means a "qualified historic building" as defined under s. 101.121 (2) (c), Stats.
SPS 366.0202 Note Note: Section 101.121 (2) (c) of the Statutes reads as follows: "Qualified historic building" means a historic building which:
  1. Is listed on, or has been nominated by the state historical society for listing on, the national register of historic places in Wisconsin or the state register of historic places;
  2. Is included in a district which is listed on, or has been nominated by the state historical society for listing on, the national register of historic places in Wisconsin or the state register of historic places, and has been determined by the state historical society to contribute to the historic significance of the district;
  2m. Is determined by the state historical society to be eligible for listing on the national register of historic places in Wisconsin or the state register of historic places;
  3. Is listed on a certified local register of historic property; or
  4. Is included in a district which is listed on a certified local register of historic property, and has been determined by the city, village, town or county to contribute to the historic significance of the district.
SPS 366.0202(2)(b) (b) Substitute the following definition for the corresponding definition in IEBC section 202: "Unsafe" means buildings, structures or equipment that are unsanitary, or that are deficient due to inadequate means of egress facilities, inadequate light and ventilation, or that constitute a fire hazard, or in which the structure or individual structural members meet the definition of "dangerous," or that are otherwise dangerous to human life or the public welfare, or that involve illegal or improper occupancy or inadequate maintenance shall be deemed unsafe.
SPS 366.0202 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08; correction in (2) made under s. 13.92 (4) (b) 7., Stats., Register February 2008 No. 626; CR 10-103: am. (2), cr. (2) (b) Register August 2011 No. 668, eff. 9-1-11.
SPS 366.0300 SPS 366.0300 Prescriptive compliance method. The requirements in IEBC Chapter 3 are not included as part of this code, except for the requirements in IEBC Section 310 when applied by IEBC Section 1301.2.5.
SPS 366.0300 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08; CR 10-103: am. Register August 2011 No. 668, eff. 9-1-11.
SPS 366.0500 SPS 366.0500 Carbon monoxide alarms for CBRF's accommodating fewer than 20 residents. These are department rules in addition to the requirements in IEBC chapter 5 and are established under the authority of s. 101.127, Stats.:
SPS 366.0500(1)(a)(a) Existing buildings converted to be community-based residential facilities accommodating fewer than 20 residents shall be provided with carbon monoxide alarms by July 1, 2013, when either one of the following conditions exists:
SPS 366.0500(1)(a)1. 1. The building contains fuel-burning appliances.
SPS 366.0500(1)(a)2. 2. The building has an attached garage.
SPS 366.0500(1)(b) (b) This section applies to community-based residential facilities described under par. (a) in existence prior to January 1, 2005.
SPS 366.0500 Note Note: Pursuant to s. 101.01 (12), Stats., an existing building converted to be community-based residential facility accommodating fewer than 20 residents is not defined to be a "public building." See also s. SPS 361.02 (5).
SPS 366.0500(2) (2) Carbon monoxide alarms shall be listed and labeled to be in conformance with one of the following standards:
SPS 366.0500(2)(a) (a) UL 2034.
SPS 366.0500(2)(b) (b) UL 2075.
SPS 366.0500(3)(a)(a) A carbon monoxide alarm shall be installed in accordance with the instructions of its manufacturer.
SPS 366.0500(3)(b) (b) A carbon monoxide alarm shall be provided on each floor level of an existing building accommodating a community-based residential facility described under sub. (1) (a), if the building contains fuel-burning appliances.
SPS 366.0500(3)(c) (c) A carbon monoxide alarm shall be provided on each floor level where sleeping units are located in an existing building accommodating a community-based residential facility described under sub. (1) (a), if the building has an attached garage and no fuel-burning appliances.
SPS 366.0500 History History: CR 10-103: cr. Register August 2011 No. 668, eff. 9-1-11.
SPS 366.0503 SPS 366.0503 Smoke alarms. These are department rules in addition to the requirements in IEBC section 503:
SPS 366.0503(1) (1) No smoke alarm, including an alarm that exists on September 1, 2011, may remain in service for more than that specified by the manufacturer.
SPS 366.0503(2) (2) The replacement of a smoke alarm that uses a battery as its primary power source shall be a new smoke alarm that complies with UL 217 and either of the following:
SPS 366.0503(2)(a) (a) The alarm is hardwired in accordance with IBC section 907.2.11.4 and has backup power in accordance with that section.
SPS 366.0503(2)(b) (b) The alarm uses, as its primary power source, a non-replaceable, non-removable battery that is capable of powering the alarm for at least 10 years.
SPS 366.0503 History History: CR 10-103: cr. Register August 2011 No. 668, eff. 9-1-11.
SPS 366.0506 SPS 366.0506 Structural evaluation. The requirements in IEBC sections 506.2 to 506.2.5 are not included as part of this code.
SPS 366.0506 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08.
SPS 366.0509 SPS 366.0509 Plumbing. The requirements in IEBC section 509 are not included as part of this code.
SPS 366.0509 Note Note: See the Wisconsin Uniform Plumbing Code, chs. SPS 382 to 387, for plumbing and water conservation provisions.
SPS 366.0509 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08.
SPS 366.0602 SPS 366.0602 Building elements and materials.
SPS 366.0602(1)(1) Materials and methods. Substitute the following wording for the requirements in IEBC section 602.4: All new work shall comply with materials and methods requirements in the IBC, IECC, IFGC, IMC, and IPC, as applicable, that specify material standards, detail of installation and connection, joints, penetrations, and continuity of any element, component, or system in the building.
SPS 366.0602(2) (2)International fuel gas code. The requirements in IEBC section 602.4.1 are not included as part of this code.
SPS 366.0602 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08; CR 10-103: am. Register August 2011 No. 668, eff. 9-1-11.
SPS 366.0604 SPS 366.0604 Stairway width. This is a department rule in addition to the requirements in IEBC section 604: Where installing an inclined platform lift or stairway chairlift, the clear-passage width shall be provided with the lift in the unfolded, usable position — except where an existing, previously approved lift is being replaced, the clear-passage width may remain as it was with the original lift in place, but it may not be reduced by the replacement.
SPS 366.0604 History History: CR 14-020: cr. Register August 2014 No. 704, eff. 9-1-14.
SPS 366.0605 SPS 366.0605 Lifts.
SPS 366.0605(1)(1) Substitute the following wording for the requirements in ICC/ANSI A117.1 section 410.2.1 as referenced by IEBC section 605.1:
SPS 366.0605(1)(a) (a) Doors and gates shall be low energy power operated doors or gates complying with ICC/ANSI A117.1 section 404.3, except as provided in par. (b). Doors shall remain open for 20 seconds minimum. On lifts with one door or with doors on opposite ends, the end door clear opening width shall be 32 inches minimum. On lifts with one door on a narrow end and one door on a long side, the end door clear opening width shall be 36 inches minimum. Side door clear opening width shall be 42 inches minimum. Where a door is provided on a long side and on a narrow end of a lift, the side door shall be located with either the strike side or the hinge side in the corner furthest from the door on the narrow end.
SPS 366.0605(1)(b)1.1. A door or gate providing access to a narrow end of a platform that serves only one landing shall be permitted to be of the manual-opening, self-closing type, where clearance at the door or gate complies with the requirements in ICC/ANSI A117.1 sections 404.2.3.1, 404.2.3.4, and 404.2.5, and the floor surface is not steeper than 1:48.
SPS 366.0605(1)(b)2. 2. Lifts serving 2 landings maximum and having doors or gates on adjacent sides shall be permitted to have self-closing manual doors or gates provided that the side door or gate is located with the strike side furthest from the end door and clearance at the door or gate complies with the requirements in ICC/ANSI A117.1 sections 404.2.3.1, 404.2.3.4, and 404.2.5, and the floor surface is not steeper than 1:48.
SPS 366.0605(2) (2) Substitute the following wording for the requirements in ICC/ANSI A117.1 section 410.5 as referenced by IEBC section 605.1: Clear floor space of platform lifts shall comply with one of the following:
SPS 366.0605(2)(a) (a) Platforms lifts with a single door or with doors on opposite ends shall provide a clear floor width of 36 inches minimum and a clear floor depth of 54 inches minimum.
SPS 366.0605(2)(b) (b) Platform lifts with doors on adjacent sides shall provide a clear floor width of 36 inches minimum and clear floor depth of 60 minimum.
SPS 366.0605(3) (3) These are department rules in addition to the requirements in ICC/ANSI A117.1 section 410 as referenced by IEBC section 605.1:
SPS 366.0605(3)(a) (a) Controls at platform lift landings shall comply with the requirements in ICC/ANSI A117.1 sections 407.2.1 and 407.2.1.1 to 407.2.1.4.
SPS 366.0605(3)(b) (b) Floor designations shall comply with the requirements in ICC/ANSI A117.1 section 407.2.3.1.
SPS 366.0605(3)(c) (c) Controls on the platform shall comply with the requirements in ICC/ANSI A117.1 sections 407.4.6.2 and 407.4.7.1.1 to 407.4.7.1.3.
SPS 366.0605 History History: CR 14-020: cr. Register August 2014 No. 704, eff. 9-1-14.
SPS 366.0607 SPS 366.0607 Energy conservation requirements. Substitute the following wording for the requirements in IEBC section 607.1:
SPS 366.0607(1) (1)Additions, alterations, renovations or repairs. Except as specified in sub. (2), additions, alterations, renovations or repairs to an existing building, building system or portion thereof shall conform to the provisions of IECC as they relate to new construction without requiring the unaltered portions of the existing building or building system to comply with the IECC. Additions, alterations, renovations, or repairs shall not create an unsafe or hazardous condition or overload existing building systems.
SPS 366.0607(2) (2)Exceptions. All of the following need not comply provided the energy use of the building is not increased:
SPS 366.0607(2)(a) (a) Storm windows installed over existing fenestration.
SPS 366.0607(2)(b) (b) Glass only replacements in an existing sash and frame.
SPS 366.0607(2)(c) (c) Existing ceiling, wall or floor cavities exposed during construction provided that these cavities are filled with insulation.
SPS 366.0607(2)(d) (d) Construction where the existing roof, wall or floor cavity is not exposed.
SPS 366.0607(2)(e) (e) Reroofing for roofs where neither the sheathing nor the insulation is exposed.
SPS 366.0607(2)(f) (f) Replacement of existing doors that separate conditioned space from the exterior shall not require the installation of a vestibule or revolving door, provided, however, that an existing vestibule that separates a conditioned space from the exterior shall not be removed.
SPS 366.0607(2)(g) (g) Alterations that replace less than 50 percent of the luminaires in a space, provided that such alterations do not increase the installed interior lighting power.
SPS 366.0607(2)(h) (h) Alterations that replace only the bulb and ballast within the existing luminaires in a space provided that the alteration does not increase the installed interior lighting power.
SPS 366.0607(3) (3)Reroofing. This is a department rule in addition to the requirements in IEBC section 607: Roofs without insulation in the cavity and where the sheathing or insulation is exposed during reroofing shall be insulated either above or below the sheathing.
SPS 366.0607 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08; CR 10-103: cr. (2) (e) to (h), (3) Register August 2011 No. 668, eff. 9-1-11.
SPS 366.0704 SPS 366.0704 Automatic sprinkler systems. This is a department exception to the requirement in IEBC section 704.2: The installation or extension of an automatic sprinkler system may exclude the protection of combustible concealed spaces that are not accessible in existing buildings.
SPS 366.0704 History History: CR 10-103: renum. from Comm 66.0701 and am. Register August 2011 No. 668, eff. 9-1-11.
SPS 366.0709 SPS 366.0709 Altered existing mechanical systems. The exception to the requirements in IEBC section 709.1 and the requirements in IEBC section 709.2 are not included as part of this code.
SPS 366.0709 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08.
SPS 366.0710 SPS 366.0710 Minimum plumbing fixtures. Substitute the following wording for the requirements in IEBC section 710.1: Where the occupant load of a story is increased by more than 20 percent, plumbing fixtures for the story shall be provided in quantities specified in the IBC based on the increased occupant load.
SPS 366.0710 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08.
SPS 366.0711 SPS 366.0711 Minimum energy conservation requirements. Substitute the following wording for the requirements in IEBC section 711: Level 2 alterations to existing buildings or structures shall comply with s. SPS 366.0607.
SPS 366.0711 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08; correction made under s. 13.92 (4) (b) 7., Stats., Register February 2008 No. 626; correction made under s. 13.92 (4) (b) 7., Stats., Register December 2011 No. 672.
SPS 366.0802 SPS 366.0802 Emergency Controls. The requirements in IEBC section 802.2.1 are not included as part of this code.
SPS 366.0802 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08.
SPS 366.0808 SPS 366.0808 Minimum energy conservation requirements. Substitute the following wording for the requirements in IEBC section 808.1: Level 3 alterations to existing buildings or structures shall comply with s. SPS 366.0607.
SPS 366.0808 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08; correction made under s. 13.92 (4) (b) 7., Stats., Register February 2008 No. 626; correction made under s. 13.92 (4) (b) 7., Stats., Register December 2011 No. 672.
SPS 366.0809 SPS 366.0809 Plumbing. These are department rules in addition to the requirements in IEBC chapter 8:
SPS 366.0809(1) (1) Pursuant to s. 101.128, Stats., level 3 alterations within an existing facility where the public congregates shall necessitate that plumbing fixtures serving the work area be provided in a ratio of at least 2 water closets for females as to each water closet and urinal for the males.
SPS 366.0809(2)(a)(a) Under this section "facility where the public congregates" has the meaning has given in s. 101.128 (1) (b), Stats.
SPS 366.0809 Note Note: Section 101.128 (1) (b), Stats., reads: "Facility where the public congregates" means any of the following that has a general capacity or a seating capacity of 500 or more persons:
SPS 366.0809 Note 1. An amusement facility.
SPS 366.0809 Note 2. A convention or trade hall or center.
SPS 366.0809 Note 3. A specialty event center.
SPS 366.0809 Note 4. A sports or entertainment arena, center or building.
SPS 366.0809 Note 5. A stadium.
SPS 366.0809 Note 6. An airport, bus terminal, train station or other transportation center.
SPS 366.0809(2)(b) (b) Under this section "alterations" has the meaning has given in s. 101.128 (1) (d), Stats., for "renovation".
Loading...
Loading...
Published under s. 35.93, Stats. Updated on the first day of each month. Entire code is always current. The Register date on each page is the date the chapter was last published.