SPS 366.0500(2)(b) (b) UL 2075.
SPS 366.0500(3)(a)(a) A carbon monoxide alarm shall be installed in accordance with the instructions of its manufacturer.
SPS 366.0500(3)(b) (b) A carbon monoxide alarm shall be provided on each floor level of an existing building accommodating a community-based residential facility described under sub. (1) (a), if the building contains fuel-burning appliances.
SPS 366.0500(3)(c) (c) A carbon monoxide alarm shall be provided on each floor level where sleeping units are located in an existing building accommodating a community-based residential facility described under sub. (1) (a), if the building has an attached garage and no fuel-burning appliances.
SPS 366.0500 History History: CR 10-103: cr. Register August 2011 No. 668, eff. 9-1-11.
SPS 366.0503 SPS 366.0503Smoke alarms. These are department rules in addition to the requirements in IEBC section 503:
SPS 366.0503(1) (1) No smoke alarm, including an alarm that exists on September 1, 2011, may remain in service for more than that specified by the manufacturer.
SPS 366.0503(2) (2) The replacement of a smoke alarm that uses a battery as its primary power source shall be a new smoke alarm that complies with UL 217 and either of the following:
SPS 366.0503(2)(a) (a) The alarm is hardwired in accordance with IBC section 907.2.11.4 and has backup power in accordance with that section.
SPS 366.0503(2)(b) (b) The alarm uses, as its primary power source, a non-replaceable, non-removable battery that is capable of powering the alarm for at least 10 years.
SPS 366.0503 History History: CR 10-103: cr. Register August 2011 No. 668, eff. 9-1-11.
SPS 366.0506 SPS 366.0506Structural evaluation. The requirements in IEBC sections 506.2 to 506.2.5 are not included as part of this code.
SPS 366.0506 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08.
SPS 366.0509 SPS 366.0509Plumbing. The requirements in IEBC section 509 are not included as part of this code.
SPS 366.0509 Note Note: See the Wisconsin Uniform Plumbing Code, chs. SPS 382 to 387, for plumbing and water conservation provisions.
SPS 366.0509 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08.
SPS 366.0602 SPS 366.0602Building elements and materials.
SPS 366.0602(1)(1)Materials and methods. Substitute the following wording for the requirements in IEBC section 602.4: All new work shall comply with materials and methods requirements in the IBC, IECC, IFGC, IMC, and IPC, as applicable, that specify material standards, detail of installation and connection, joints, penetrations, and continuity of any element, component, or system in the building.
SPS 366.0602(2) (2)International fuel gas code. The requirements in IEBC section 602.4.1 are not included as part of this code.
SPS 366.0602 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08; CR 10-103: am. Register August 2011 No. 668, eff. 9-1-11.
SPS 366.0604 SPS 366.0604Stairway width. This is a department rule in addition to the requirements in IEBC section 604: Where installing an inclined platform lift or stairway chairlift, the clear-passage width shall be provided with the lift in the unfolded, usable position — except where an existing, previously approved lift is being replaced, the clear-passage width may remain as it was with the original lift in place, but it may not be reduced by the replacement.
SPS 366.0604 History History: CR 14-020: cr. Register August 2014 No. 704, eff. 9-1-14.
SPS 366.0605 SPS 366.0605Lifts.
SPS 366.0605(1) (1) Substitute the following wording for the requirements in ICC/ANSI A117.1 section 410.2.1 as referenced by IEBC section 605.1:
SPS 366.0605(1)(a) (a) Doors and gates shall be low energy power operated doors or gates complying with ICC/ANSI A117.1 section 404.3, except as provided in par. (b). Doors shall remain open for 20 seconds minimum. On lifts with one door or with doors on opposite ends, the end door clear opening width shall be 32 inches minimum. On lifts with one door on a narrow end and one door on a long side, the end door clear opening width shall be 36 inches minimum. Side door clear opening width shall be 42 inches minimum. Where a door is provided on a long side and on a narrow end of a lift, the side door shall be located with either the strike side or the hinge side in the corner furthest from the door on the narrow end.
SPS 366.0605(1)(b)1.1. A door or gate providing access to a narrow end of a platform that serves only one landing shall be permitted to be of the manual-opening, self-closing type, where clearance at the door or gate complies with the requirements in ICC/ANSI A117.1 sections 404.2.3.1, 404.2.3.4, and 404.2.5, and the floor surface is not steeper than 1:48.
SPS 366.0605(1)(b)2. 2. Lifts serving 2 landings maximum and having doors or gates on adjacent sides shall be permitted to have self-closing manual doors or gates provided that the side door or gate is located with the strike side furthest from the end door and clearance at the door or gate complies with the requirements in ICC/ANSI A117.1 sections 404.2.3.1, 404.2.3.4, and 404.2.5, and the floor surface is not steeper than 1:48.
SPS 366.0605(2) (2) Substitute the following wording for the requirements in ICC/ANSI A117.1 section 410.5 as referenced by IEBC section 605.1: Clear floor space of platform lifts shall comply with one of the following:
SPS 366.0605(2)(a) (a) Platforms lifts with a single door or with doors on opposite ends shall provide a clear floor width of 36 inches minimum and a clear floor depth of 54 inches minimum.
SPS 366.0605(2)(b) (b) Platform lifts with doors on adjacent sides shall provide a clear floor width of 36 inches minimum and clear floor depth of 60 minimum.
SPS 366.0605(3) (3) These are department rules in addition to the requirements in ICC/ANSI A117.1 section 410 as referenced by IEBC section 605.1:
SPS 366.0605(3)(a) (a) Controls at platform lift landings shall comply with the requirements in ICC/ANSI A117.1 sections 407.2.1 and 407.2.1.1 to 407.2.1.4.
SPS 366.0605(3)(b) (b) Floor designations shall comply with the requirements in ICC/ANSI A117.1 section 407.2.3.1.
SPS 366.0605(3)(c) (c) Controls on the platform shall comply with the requirements in ICC/ANSI A117.1 sections 407.4.6.2 and 407.4.7.1.1 to 407.4.7.1.3.
SPS 366.0605 History History: CR 14-020: cr. Register August 2014 No. 704, eff. 9-1-14.
SPS 366.0607 SPS 366.0607Energy conservation requirements. Substitute the following wording for the requirements in IEBC section 607.1:
SPS 366.0607(1) (1)Additions, alterations, renovations or repairs. Except as specified in sub. (2), additions, alterations, renovations or repairs to an existing building, building system or portion thereof shall conform to the provisions of IECC as they relate to new construction without requiring the unaltered portions of the existing building or building system to comply with the IECC. Additions, alterations, renovations, or repairs shall not create an unsafe or hazardous condition or overload existing building systems.
SPS 366.0607(2) (2)Exceptions. All of the following need not comply provided the energy use of the building is not increased:
SPS 366.0607(2)(a) (a) Storm windows installed over existing fenestration.
SPS 366.0607(2)(b) (b) Glass only replacements in an existing sash and frame.
SPS 366.0607(2)(c) (c) Existing ceiling, wall or floor cavities exposed during construction provided that these cavities are filled with insulation.
SPS 366.0607(2)(d) (d) Construction where the existing roof, wall or floor cavity is not exposed.
SPS 366.0607(2)(e) (e) Reroofing for roofs where neither the sheathing nor the insulation is exposed.
SPS 366.0607(2)(f) (f) Replacement of existing doors that separate conditioned space from the exterior shall not require the installation of a vestibule or revolving door, provided, however, that an existing vestibule that separates a conditioned space from the exterior shall not be removed.
SPS 366.0607(2)(g) (g) Alterations that replace less than 50 percent of the luminaires in a space, provided that such alterations do not increase the installed interior lighting power.
SPS 366.0607(2)(h) (h) Alterations that replace only the bulb and ballast within the existing luminaires in a space provided that the alteration does not increase the installed interior lighting power.
SPS 366.0607(3) (3)Reroofing. This is a department rule in addition to the requirements in IEBC section 607: Roofs without insulation in the cavity and where the sheathing or insulation is exposed during reroofing shall be insulated either above or below the sheathing.
SPS 366.0607 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08; CR 10-103: cr. (2) (e) to (h), (3) Register August 2011 No. 668, eff. 9-1-11.
SPS 366.0704 SPS 366.0704Automatic sprinkler systems. This is a department exception to the requirement in IEBC section 704.2: The installation or extension of an automatic sprinkler system may exclude the protection of combustible concealed spaces that are not accessible in existing buildings.
SPS 366.0704 History History: CR 10-103: renum. from Comm 66.0701 and am. Register August 2011 No. 668, eff. 9-1-11.
SPS 366.0709 SPS 366.0709Altered existing mechanical systems. The exception to the requirements in IEBC section 709.1 and the requirements in IEBC section 709.2 are not included as part of this code.
SPS 366.0709 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08.
SPS 366.0710 SPS 366.0710Minimum plumbing fixtures. Substitute the following wording for the requirements in IEBC section 710.1: Where the occupant load of a story is increased by more than 20 percent, plumbing fixtures for the story shall be provided in quantities specified in the IBC based on the increased occupant load.
SPS 366.0710 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08.
SPS 366.0711 SPS 366.0711Minimum energy conservation requirements. Substitute the following wording for the requirements in IEBC section 711: Level 2 alterations to existing buildings or structures shall comply with s. SPS 366.0607.
SPS 366.0711 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08; correction made under s. 13.92 (4) (b) 7., Stats., Register February 2008 No. 626; correction made under s. 13.92 (4) (b) 7., Stats., Register December 2011 No. 672.
SPS 366.0802 SPS 366.0802Emergency Controls. The requirements in IEBC section 802.2.1 are not included as part of this code.
SPS 366.0802 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08.
SPS 366.0808 SPS 366.0808Minimum energy conservation requirements. Substitute the following wording for the requirements in IEBC section 808.1: Level 3 alterations to existing buildings or structures shall comply with s. SPS 366.0607.
SPS 366.0808 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08; correction made under s. 13.92 (4) (b) 7., Stats., Register February 2008 No. 626; correction made under s. 13.92 (4) (b) 7., Stats., Register December 2011 No. 672.
SPS 366.0809 SPS 366.0809Plumbing. These are department rules in addition to the requirements in IEBC chapter 8:
SPS 366.0809(1) (1) Pursuant to s. 101.128, Stats., level 3 alterations within an existing facility where the public congregates shall necessitate that plumbing fixtures serving the work area be provided in a ratio of at least 2 water closets for females as to each water closet and urinal for the males.
SPS 366.0809(2)(a)(a) Under this section “facility where the public congregates" has the meaning has given in s. 101.128 (1) (b), Stats.
SPS 366.0809 Note Note: Section 101.128 (1) (b), Stats., reads: “Facility where the public congregates" means any of the following that has a general capacity or a seating capacity of 500 or more persons:
SPS 366.0809 Note 1. An amusement facility.
SPS 366.0809 Note 2. A convention or trade hall or center.
SPS 366.0809 Note 3. A specialty event center.
SPS 366.0809 Note 4. A sports or entertainment arena, center or building.
SPS 366.0809 Note 5. A stadium.
SPS 366.0809 Note 6. An airport, bus terminal, train station or other transportation center.
SPS 366.0809(2)(b) (b) Under this section “alterations" has the meaning has given in s. 101.128 (1) (d), Stats., for “renovation".
SPS 366.0809 Note Note: Section 101.128 (1) (d), Stats., reads: “Renovation" means any structural remodeling, improvement or alteration of an existing facility where the public congregates. “Renovation" does not include any of the following:
SPS 366.0809 Note 1. Reroofing.
SPS 366.0809 Note 2. Cosmetic remodeling, including painting or the installation of wall covering, of paneling, of floor covering or of suspended ceilings.
SPS 366.0809 Note 3. An alteration to an electrical or mechanical system.
SPS 366.0809 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08.
SPS 366.0901 SPS 366.0901Change of occupancy.
SPS 366.0901(1) (1)Change in occupancy with no occupancy classification. Substitute the following wording for the requirements in IEBC section 901.2: A change in occupancy, as defined in IEBC section 202, with no change of occupancy classification may not be made to any structure that will subject the structure to any special provisions of this code, including the provisions of IEBC sections 902 through 911, without the approval of the code official.
SPS 366.0901(2) (2)Change of occupancy classification. This is a department rule in addition to the requirements in IEBC section 901.3: Buildings undergoing a change in occupancy that would result in an increase in demand for either fossil fuel or electrical energy shall comply with IECC.
SPS 366.0901(3) (3)Certification of occupancy required. The requirements in IEBC section 901.4 are not included as part of this code.
SPS 366.0901(4) (4)Standpipe systems. This is a department rule in addition to the requirements in IEBC section 912.2: Standpipe systems shall be provided in existing buildings and structures or portions of existing buildings and structures in accordance with chapter 9 of the IBC when existing buildings or structures that are greater than 60 feet in height are changed to include a Group R-1 or R-2 occupancy.
SPS 366.0901 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08; CR 10-103: am. (1) Register August 2011 No. 668, eff. 9-1-11.
SPS 366.0911 SPS 366.0911Other requirements.
SPS 366.0911(1) (1)Elevator recall. This is a department rule in addition to the requirements in IEBC section 911: At least one existing elevator shall be provided with emergency recall operation and emergency in-car operation complying with ch. SPS 318 when an existing building or structure that is greater than 60 feet in height is changed to include a Group R-1 or R-2 occupancy.
SPS 366.0911(2) (2)Carbon monoxide alarms. This is a department rule in addition to the requirements in IEBC section 911: A building or a portion of a building changed to be or include a residential building as defined under s. 101.149 (1) (b), Stats., shall be provided with carbon monoxide alarms or detectors in accordance with s. SPS 362.1200.
SPS 366.0911 History History: CR 06-120: cr. Register February 2008 No. 626, eff. 3-1-08; EmR0826: emerg. renum. to be (1), cr. (1) (title) and (2), eff. 10-1-08; CR 08-085: renum. to be (1), cr. (1) (title) and (2) Register May 2009 No. 641, eff. 6-1-09; correction in (1), (2) made under s. 13.92 (4) (b) 7., Stats., Register December 2011 No. 672.
Loading...
Loading...
Published under s. 35.93, Stats. Updated on the first day of each month. Entire code is always current. The Register date on each page is the date the chapter was last published.