SPS 382.40(8)(b)1.1. Exterior water supply piping may not be located in, under or above sanitary sewer manholes, or POWTS treatment, holding or dispersal components.
SPS 382.40(8)(b)2. 2. If a private water main or a water service crosses a sanitary sewer, the water piping within 5 feet of the point of crossing shall be installed in accordance with any of the following requirements:
SPS 382.40(8)(b)2.a. a. The water piping shall be installed at least 12 inches above the top of the sewer.
SPS 382.40(8)(b)2.b. b. The water piping shall be installed at least 18 inches below the bottom of the sewer.
SPS 382.40(8)(b)2.c. c. The water or sewer piping shall be installed within a waterproof sleeve made of materials as specified for sanitary building sewers in s. SPS 384.30 (2).
SPS 382.40(8)(b)3. 3. Except as permitted in subds. 4 and 5., private water mains and water services shall be installed at least 5 feet horizontally from any sanitary sewer.
SPS 382.40 Note Note: The Department of Natural Resources has limitations for the separation of water mains and sanitary sewers.
SPS 382.40(8)(b)4. 4. Private water mains and water services may be installed less than 5 feet horizontally from a pressurized sanitary sewer if all of the following conditions are met:
SPS 382.40(8)(b)4.a. a. The bottom of the water piping is installed at least 18 inches above the pressurized sewer.
SPS 382.40(8)(b)4.b. b. The water piping is installed at least 3 feet horizontally from the pressurized sewer.
SPS 382.40(8)(b)5. 5. Private water mains and water services may be installed less than 5 feet horizontally from a non-pressurized sanitary sewer if any of the following conditions are met:
SPS 382.40(8)(b)5.a. a. The bottom of the water piping is installed at least 12 inches above the sewer.
SPS 382.40(8)(b)5.b. b. The sewer is constructed of materials listed in Table 384.30-2.
SPS 382.40(8)(b)5.c. c. The water service is 2 inches or less in diameter and is located more than 24 inches from the sewer.
SPS 382.40(8)(b)6. 6. The portion of a private water main or water service within 5 feet of developed length from the point where the water service first enters the building may be less than 12 inches above the sewer and within 24 inches of the sewer.
SPS 382.40(8)(b)7. 7. No private water main or water service may be installed within 6 inches of a storm sewer.
SPS 382.40 Note Note: See ch. SPS 382 Appendix A-382.30 (11) (d) for setback distance from yard hydrant to well.
SPS 382.40 Note Note: See ch. SPS 383 Table 383.43–1 for setback distances to POWTS components.
SPS 382.40(8)(b)9. 9. No underground water supply storage tank shall be installed within 8 feet of a storage vessel containing a substance of a higher hazard than that contained in the water supply storage tank.
SPS 382.40(8)(c) (c) Limitations. No private water main or water service may pass through or under a building to serve another building unless one of the following conditions are met:
SPS 382.40(8)(c)1. 1. The private water main or water service serves farm buildings or farm houses, or both that are all located on one property.
SPS 382.40(8)(c)2. 2. The private water main or water service serves buildings that are located on the same property and a document which indicates that the piping and distribution arrangement for the property and buildings will be recorded with the register of deeds no later than 90 days after installation.
SPS 382.40(8)(d) (d) Water distribution piping.
SPS 382.40(8)(d)1.1. Water distribution piping shall be supported in accordance with s. SPS 382.60.
SPS 382.40(8)(d)2. 2. Provisions shall be made to evacuate all water out of the water distribution system.
SPS 382.40(8)(d)3.a.a. Except where parallel water meters are installed, water distribution piping shall be provided to bypass a water meter 1½ or larger.
SPS 382.40(8)(d)3.b. b. The minimum diameter of water distribution piping serving as a meter bypass shall be one nominal pipe size smaller than the meter.
SPS 382.40(8)(d)4. 4. Except as provided in subds. 5. and 6., a bypass shall be provided to serve a water treatment device. The bypass piping may be an internal part of the water treatment device.
SPS 382.40(8)(d)5. 5. A bypass shall not be required when a water treatment device serves no more than 2 fixtures or outlets.
SPS 382.40(8)(d)6. 6. A bypass shall be prohibited for a water treatment device installed to reduce a contaminant in order to comply with the provisions in s. SPS 382.70 (3).
SPS 382.40(8)(e) (e) Valves.
SPS 382.40(8)(e)1.1. All control valves installed in a water service, except a valve serving only as a corporation cock, shall be accessible.
SPS 382.40(8)(e)2. 2. Stop- and waste-type control valves may not be installed underground except in the following situations:
SPS 382.40(8)(e)2.a. a. Fire hydrants intended for fire fighting.
SPS 382.40(8)(e)2.b. b. Two-inch and larger diameter hydrants serving municipal wastewater treatment plants.
SPS 382.40(8)(e)2.c. c. Emergency fixtures.
SPS 382.40(8)(e)3. 3. All control valves and fixture stop valves installed in a water distribution system shall be accessible. Control valves for the individual plumbing fixtures and appliances within dwelling units shall be accessible from within the dwelling unit.
SPS 382.40(8)(f) (f) Water hammer arrestors. All plumbing fixtures, appliances and appurtenances with 3/8" or larger inlet openings and with solenoid actuated quick closing valves shall be provided with water hammer arrestors. Water hammer arrestors shall be installed in the fixture supplies serving the fixtures, appliances or appurtenances. Water hammer arrestors shall be accessible.
SPS 382.40(8)(g) (g) Temperature control. The water temperature to all showers in public buildings shall be controlled by thermostatic or combination thermostatic-pressure balanced mixing valves or by individually controlled pressure balanced mixing valves. A thermostatic or combination thermostatic-pressure balanced mixing valve may not be bypassed.
SPS 382.40(8)(h) (h) Fittings and connections. The drilling and tapping of water supply piping shall be prohibited except for:
SPS 382.40(8)(h)1. 1. Corporation cocks for a water service or a private water main; and
SPS 382.40(8)(h)2. 2. Self-tapping valves which serve individual plumbing appliances.
SPS 382.40(8)(i) (i) Flushing and disinfection of potable water supply systems.
SPS 382.40(8)(i)1.a.a. Before a newly constructed water supply system is to be put into use, the piping of the system shall be filled with water and allowed to stand for at least 24 hours. After 24 hours each water outlet shall be flushed beginning with the outlet closest to the building control valve and then each successive outlet in the system. The flushing at each water outlet shall continue for at least one minute and until the water appears clear at the outlet.
SPS 382.40(8)(i)1.b. b. Each portion of a water supply system which is altered or repaired shall be flushed for at least one minute and until the water appears clear.
SPS 382.40(8)(i)2. 2. New private water mains and extensions to private water mains shall be disinfected prior to use in accordance with AWWA C651 or the following method:
SPS 382.40(8)(i)2.a. a. The pipe system shall be flushed with clean water until no dirty water appears at the points of outlet.
SPS 382.40(8)(i)2.b. b. The system or part thereof shall be filled with a solution of water and chlorine containing at least 50 parts per million of chlorine and the system or part thereof shall be valved off and allowed to stand for 24 hours or the system or part thereof shall be filled with a solution of water and chlorine containing at least 200 parts per million of chlorine and allowed to stand for 3 hours.
SPS 382.40(8)(i)2.c. c. Following the allowed standing time, the system shall be flushed with clean potable water.
SPS 382.40(8)(i)2.d. d. The procedures shall be repeated if it is shown by a bacteriological examination that contamination still exists in the system.
SPS 382.40(8)(i)3. 3. The department may require a water quality analysis to be done for a new or repaired water supply system. The analysis shall be performed in accordance with acceptable nationally recognized laboratory practices. If the water supply system has been disinfected, water samples for the analysis may not be taken sooner than 24 hours after disinfection.
SPS 382.40 Note Note: See s. SPS 384.30 (1) regarding the bending of pipe and protection from puncture.
SPS 382.40(8)(i)4. 4. New or repaired combination water services or combination private water mains shall be flushed and disinfected prior to use in accordance with NFPA 24.
SPS 382.40(8)(j) (j) Water softeners. Ion exchange water softeners used primarily for water hardness reduction that, during regeneration, discharge a brine solution shall be of a demand initiated regeneration type equipped with a water meter or a sensor unless a wastewater treatment system downstream of the water softener specifically documents the reduction of chlorides.
SPS 382.40(8)(k) (k) Locating requirements.
SPS 382.40(8)(k)1.1. A means to locate buried non-metallic water services and private water mains connected to municipal supply systems shall be provided in accordance with the options under s. SPS 382.30 (11) (h), except as provided in subds. 2. and 3.
SPS 382.40(8)(k)2. 2. Tracer wire insulation color for non-metallic, potable water pipe shall be blue.
SPS 382.40(8)(k)3. 3. Tracer wire insulation color for non-metallic, non-potable water pipe shall be purple.
SPS 382.40 History History: 1-2-56; r. and recr. Register, November, 1972, No. 203, eff. 12-1-72; r. and recr. Register, February, 1979, No. 278, eff. 3-1-79; renum. from H 62.13, Register, July, 1983, No. 331, eff. 8-1-83; renum. from ILHR 82.13 and r. and recr. (2) (b) and (4) (d) 1., am. (4) (c) 3. and (6) (a) (intro.), cr. (6) (b), Register, February, 1985, No. 350, eff. 3-1-85; r. and recr. Register, May, 1988, No. 389, eff. 6-1-88; am. (5) (d) 5. a., r. and recr. (7) (h) 1. and (8) (c), renum. (8) (c) 2. to 6. to be (8) (b) 4. to 8. and am. (8) (b) 4. c., Register, August, 1991, No. 428, eff. 9-1-91; am. (8) (b) 1. and 2., Register, April, 1992, No. 436, eff. 5-1-92; renum. (3) (c) and (8) (a) to be (3) (c) 2. and (8) (a) 1. and am. (8) (a) 1., cr. (3) (c) 1., (e), (8) (a) 2. and Table 82.40-9, am. (7) (c), r. (3) (b) 1. b. and c., Register, February, 1994, No. 458, eff. 3-1-94; r. (5) (b) 3., renum. (5) (b) 4., 5. to be (5) (b) 3., 4., Register, December, 1996, No. 480, eff. 4-1-96; correction in (5) (b) 3., made under s. 13.93 (2m) (b) 7., Stats., Register, October, 1996, No. 490; r. and recr. (5) (b), Register, February, 1997, No. 494, eff. 4-1-97; reprinted to restore dropped copy, Register, April, 1997, No. 496; am. (3) (e) and (8) (b) 1. and 2., r. (8) (b) 3. and cr. (3) (f) and (8) (j), Register, April, 2000, No. 532, eff. 7-1-00; except (3) (f) eff. 5-1-00; cr. (3) (d) 3., am. (8) (g) and (i) 2., Register, December, 2000, No. 540, eff. 1-1-01; except (3) (d) 3., eff. 9-1-01; CR 02-002: r. and recr. (3) (a), (d) 1. (intro.) to b., (7) (h), (8) (c) and Tables 82.40-4 to 11, cr. (3) (a) 2., (c) 3. and (d) 1. h., am. (3) (b) 1., (4) (c) 1. b. and 2. b., (7) (d) 1. a. and b., (8) (d) 4., (g), and Tables 82.40-1 and 2, r. (3) (e), renum. (3) (f) and (8) (b) 4. to 8. to be (3) (e) and (8) (b) 3. to 7., Register April 2003 No. 568, eff. 5-1-03; CR 02-129: am. (4) (c) 1. b. Register January 2004 No. 577, eff. 2-1-04, correction in (8) (b) 5. made under s. 13.93 (2m) b. 7., Stats., Register January 2004 No. 577; CR 04-035: r. (3) (e) 2. c., r. and recr. Table 82.40-9, cr. (8) (i) 4. Register November 2004 No. 587, eff. 12-1-04; CR 06-120: r. and recr. (3) (e) 2. b., cr. (3) (e) 2. c. Register February 2008 No. 626, eff. 3-1-08; CR 07-069: cr. (8) (k) Register February 2008 No. 626, eff. 3-1-08; CR 07-100: am. (8) (b) 2. Register September 2008 No. 633, eff. 10-1-08; CR 08-055: am. (3) (b) 1. b., (d) 3. (intro.), (5) (c), (6) (a), (7) (d) 1. b., (8) (b) 2., (j), Tables 82.40-1 and 82.40-2, r. and recr. (3) (e), (8) (e) 2., cr. (8) (b) 8., (d) 3. b. and Table 82.40-3e, renum. (8) (d) 3. to be (8) (d) 3. a. Register February 2009 No. 638, eff. 3-1-09; CR 10-064: am. (3) (a) (title), (c) 1., (5) (a), (6) (a), (8) (b) 3. to 6.,Table 82.40-8 (title) and Table 82.40-10 (title), r. and recr. (3) (d) 1., renum. (3) (d) 2., 3. and Table 82.40-1 to be (3) (d) 3., 4. and Table 82.40-1b, cr. (3) (d) 2., (8) (b) 9., Table 82.40-1a, r. (9) Register December 2010 No. 660, eff. 1-1-11; CR 10-103: r. (3) (e) 2. b. to 2. d., renum. (3) (e) 2. a. to (3) (e) 2., Register August 2011 No. 668, eff. 9-1-11; correction in (2), (3) (a) 1., 2., (c) 2., 3. a., (d) 1. a., b., e., g., 2., 4. b., (5) (b) 4., (c), (d) 5. a., e., (6) (a), (7) (c), (8) (a) 1., (b) 3. c., 5. b., (d) 1., 6., (k) 1., Table 382.40-3e made under s. 13.92 (4) (b) 6., 7., Stats., Register December 2011 No. 672; CR 11-031: r. (8) (b) 2., 8., renum. (8) (b) 3., 4. to (8) (b) 2., 3., am. (8) (b) 3., cr. (8) (b) 4., am. (8) (b) 5. (intro.), 7. Register June 2013 No. 690, eff. 7-1-13; CR 13-046: am. (6) (a) Register December 2013 No. 696, eff. 1-1-14.
Table 382.40-4
- See PDF for diagram PDFMAXIMUM ALLOWABLE LOAD FOR COPPER TUBING-TYPE K, ASTM B88; (C=150)
Table 382.40-5
- See PDF for diagram PDFMAXIMUM ALLOWABLE LOAD FOR COPPER TUBING-TYPE L, ASTM B88; (C=150)
Table 382.40-6
- See PDF for diagram PDFMAXIMUM ALLOWABLE LOAD FOR COPPER TUBING-TYPE M, ASTM B88; (C=150)
Table 382.40-7
- See PDF for diagram PDFMAXIMUM ALLOWABLE LOAD FOR GALVANIZED STEEL PIPE, SCHEDULE 40, ASTM A53; (C=150)
Table 382.40-8
- See PDF for diagram PDFCHLORINATED POLYVINYL CHLORIDE TUBING, ASTM D2846 and F442, SDR 11; (C=150)
Table 382.40-9
MAXIMUM ALLOWABLE LOAD FOR CROSSLINKED POLYETHYLENE (PEX) TUBING,
ASTM F876 and F877; (C=150) - See PDF for diagram PDF
Table 382.40-10
- See PDF for diagram PDFMAXIMUM ALLOWABLE LOAD FOR CHLORINATED POLYVINYL CHLORIDE TUBING, ASTM F442, SDR 13.5; (C=150)
Table 382.40-11
- See PDF for diagram PDFMAXIMUM ALLOWABLE LOAD FOR POLYETHYLENE ALUMINUM POLYETHYLENE TUBING (PexAlPex), ASTM F1281; (C=150)
SPS 382.41 SPS 382.41Cross connection control.
SPS 382.41(1) (1)Scope. The provisions of this section set forth the requirements for the protection of water within water supply systems when and where there is the possibility of contamination due to cross connections or backflow conditions.
SPS 382.41 Note Note: The Department of Natural Resources governs the operation and design of community water systems and under s. NR 811.09 requires the supplier of water to develop and implement a comprehensive cross connection control program.
SPS 382.41(2) (2)Materials.
SPS 382.41(2)(a)(a) All devices, assemblies and mechanisms intended to protect water supplies relative to cross connection or backflow shall be of a type recognized and approved in accordance with ch. SPS 384 and as described in sub. (4).
SPS 382.41(2)(b) (b) All methods including barometric loops and air gaps intended to protect water supplies relative to cross connection or backflow shall be constructed of materials suitable for water supply systems in accordance with ch. SPS 384.
SPS 382.41(3) (3)General requirements. Water supply systems and the connection of each plumbing fixture, piece of equipment, appliance or nonpotable water piping system shall be designed, installed and maintained in such a manner to prevent the contamination of water supplies by means of cross connections.
SPS 382.41(3)(a) (a) Types of cross connection control.
Loading...
Loading...
Published under s. 35.93, Stats. Updated on the first day of each month. Entire code is always current. The Register date on each page is the date the chapter was last published.