CR 23-006 Rule Text

Section 44. SPS 381.01 (195m), (197m), and (199m) are created to read:

SPS 381.01 (195m) “Process piping” means that piping which is separated from a water supply system or drain system by the acceptable methods or means specified under ch. SPS 382 and is part of a system used exclusively for refining, manufacturing, industrial or shipping purposes of every character and description.

(197m) “Public lavatory” means a lavatory located in a public restroom or located outside of a public restroom. Hand wash sinks required by Dept. of Agriculture Trade and Consumer Protection (DATCP), Dept. of Health Services (DHS), National Institute of Health (NIH), or United States Dept. of Agriculture (USDA) are considered public lavatory fixtures.

(199m) “Push-fit fitting” means a mechanical fitting that joins pipes or tubes and achieves a seal by pushing the mating pipe or tube into the fitting.

Section 45. SPS 381.01 (204) is amended to read:

SPS 381.01 (204) “Reduced pressure principle backflow preventer" means a type of cross connection control assembly which contains consisting of 2 independently-acting check valves, internally force loaded to a normally closed position and separated by an intermediate chamber or zone in which there is a hydraulically operated relief means for venting to atmosphere, internally force loaded to a normally open position. These assemblies are designed to operate under continuous pressure conditions. The assembly shall and includes include 2 properly located, tightly closing shut-off valves and 4 properly located test cocks.

Section 46. SPS 381.01 (218m) and (229m) are created to read:

SPS 381.01 (218m) “Siphonic roof drain system” means a drainage system designed to receive water collecting on a roof surface via negative pressure conditions created by roof drains that allow water to enter the stormwater piping system while minimizing the ingress of air, generating a negative differential fluid pressure within the piping system thereby inducing full-bore flow without pipe gradient.

(229m) “Special wastewater” means any wastewater containing deleterious waste material as defined in s. 382.34 (3) (b).

Section 47. SPS 381.01 (231m) is amended to read:

 

SPS 381.01 (231m) “Spill resistant vacuum breaker" means a cross connection control device assembly consisting of one check valve force loaded closed, and an air inlet force loaded open to atmosphere located downstream of the check valve,. 2 shutoff The assembly also includes 2 tightly closing shut-off valves and 2 test cocks or a no. 1 test cock and a bleed valve.

Section 48. SPS 381.01 (256m) and (260m) are created to read:

SPS 381.01 (256m) “Thermal disinfection” means a method of providing bacterial control within a water distribution system using water that is heated and initially circulated to a minimum temperature of 140°F and with a minimum temperature of 124°F at the point of return to the heat source.

 

(260m) “Trap seal primer, drainage and electric types” means a device designed to supply water to a drain trap to provide and maintain its water seal by using a supply fixture drain line, an anti-siphon fill valve for water closet tanks, flushometer valve tailpiece, or an electric trap seal primer.

Section 49. SPS 381.01 (280) is amended to read:

SPS 381.01 (280) “Water distribution system" means that portion of a water supply system from the outlet of the building control valve to the connection of a fixture supply connector, plumbing fixture, plumbing appliance, water-using equipment, or other piping systems to be served.

Section 50. SPS 381.01 (281m) is created to read:

SPS 381.01 (281m) “Water operator−in−charge” means the person designated by the owner of the building waterworks to be directly responsible for the day−to−day operations of the waterworks.

Note: Per NR 114.03(15), “waterworks” means a community water system owned by, or a private utility serving, a county, city, village, town, town sanitary district, utility district or a county−owned or state−owned public institution for congregate care or correction, which includes but is not limited to correctional institutions, correctional camp systems, county jails or houses of correction, mental health institutes, schools for the handicapped, hospitals, infirmaries and asylums.

Section 51. SPS 381.01 (282) is amended to read:

SPS 381.01 (282) “Water service" means that portion of a water supply system from the water main or private water supply up to and including the building control valve.

Section 52. SPS 381.01 (288s) is created to read:

SPS 381.01 (288s) “Yard hydrant” means a device with a water supply outlet, or faucet, that has a valve control and outlet above ground and a connection to the water supply system below ground.

Section 53. SPS 381.20 (3) is amended to read:

SPS 381.20 (3) Adoption of Standards. The standards referenced in Tables 381.20−1 to 381.20−13 are incorporated by reference into this chapter chs.381 to 387.

Section 54. Table 381.20-1 is amended to read:

Table 381.20-1

AHAM	Association of Home Appliance Manufacturers 20 North Wacker Drive 1111 19th Street, NW Suite 402 Chicago, Illinois 60606 Washington, DC 20036 Phone: [phone] Web page Website: www.aham.org

Standard Reference Number

Title

1.

DW-1 2-2005 2020

Household Electric Dishwashers

Section 55. SPS Tables 381.20-2 and 381.20-3 are repealed.

Section 56. SPS Table 381.20-3e is repealed and recreated to read:

Table 381.20-3e

ASME	American Society of Mechanical Engineers Two Park Avenue New York, New York 10016-5990 Phone: [phone] Website: www.asme.org

Standard Reference Number

Title

1.

A112.1.2-2012 (R2017)

Air Gaps in Plumbing Systems (For Plumbing Fixtures and Water-Connected Receptors)

2.

A112.1.3-2000 (R2015)

Air-gap Fittings for Use with Plumbing Fixtures, Appliances, and Appurtenances

3.

A112.3.1-2007 (R2017)

Stainless Steel Drainage Systems for Sanitary DWV, Storm and Vacuum Applications Above and Below Ground

4.

A112.3.4-2018/CSA B45.9-18

Macerating Toilet Systems and Waste Pumping Systems for Plumbing Fixtures

5.

A112.4.1-2009 (R2019)

Water Heater Relief Valve Drain Tubes

6.

A112.4.2-2015/CSA B45.16-15 (R2020)

Personal Hygiene Devices for Water Closets

7.

A112.6.1M-97 (R2017)

Supports for Off-the-Floor Plumbing Fixtures for Public Use

8.

A112.6.2-2017

Framing-Affixed Supports (Carriers) for Off-the-Floor Plumbing Fixtures

9.

A112.6.3-2019

Floor and Trench Drains

10.

A112.6.4-2003 (R2012)

Roof, Deck and Balcony Drains

11.

A112.6.9-2005 (R2015)

Siphonic Roof Drains

12.

A112.14.1-2003 (R2017)

Backwater Valves

13.

A112.14.3-2018

Hydromechanical Grease Interceptors

14.

A112.14.4-2001 (R2012)

Grease Removal Devices

15.

A112.14.6-2010

FOG (Fats, Oils and Greases) Disposal Systems

16.

A112.18.1-2018 / CSA B125.1-18

Plumbing Supply Fittings

17.

A112.18.3-2002 (R2017)

Performance Requirements for Backflow Protection Devices and Systems in Plumbing Fixture Fittings

18.

A112.18.6-2017 / CSA B125.6-17

Flexible Water Connectors

19.

A112.19.1-2018 / CSA B45.2-18

Enameled Cast Iron and Enameled Steel Plumbing Fixtures

20.

A112.19.2-2018 / CSA B45.1-18

Vitreous China Plumbing Fixtures and Hydraulic Requirements for Water Closets and Urinals

21.

A112.19.3-2017 / CSA B45.4-17

Stainless Steel Plumbing Fixtures (Designed for Residential Use)

22.

A112.19.4M-1994 (R2009)

Porcelain Enameled Formed Steel Plumbing Fixtures

23.

A112.19.5-2017 / CSA B45.15-17

Flush Valves and Spuds for Water-Closets, Urinals, and Tanks

24.

B1.20.1-2013 (R2018)

Pipe Threads, General Purpose, (Inch)

25.

B16.1-2020

Gray Iron Pipe Flanges and Flanged Fittings (Classes 25, 125, and 250)

26.

B16.3-2016

Malleable Iron Threaded Fittings (Classes 150 and 300)

27.

B16.4-2016

Gray Iron Threaded Fitting (Classes 125 and 250)

28.

B16.5-2020

Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24 Metric/Inch Standard

29.

B16.9-2018

Factory-Made Wrought Buttwelding Fittings

30.

B16.11-2016

Forged Fittings, Socket–Welding and Threaded

31.

B16.12-2019

Cast Iron Threaded Drainage Fittings

32.

B16.15-2018

Cast Bronze Threaded Fittings, (Classes 125 and 250)

33.

B16.18-2018

Cast Copper Alloy Solder Joint Pressure Fittings

34.

B16.22-2018

Wrought Copper and Copper Alloy Solder-Joint Pressure Fittings

35.

B16.23-2016

Cast Copper Alloy Solder Joint Drainage Fittings: DWV

36.

B16.24-2016

Cast Copper Alloy Pipe Flanges, Flanged Fittings, and Valves: Classes 150, 300, 600, 900, 1500, and 2500

37.

B16.26-2018

Cast Copper Alloy Fittings for Flared Copper Tubes

38.

B16.29-2017

Wrought Copper and Wrought Copper Alloy Solder Joint Drainage Fittings - DWV

39.

B16.42-2016

Ductile Iron Pipe Flanges and Flanged Fittings, (Classes 150 and 300)

40.9

B16.45-1998 (R 2006)

Cast Iron Fittings for Sovent® Drainage Systems

41.

B36.19M-2018

Stainless Steel Pipe

Section 57. SPS Table 381.20-3p is created to read:

Table 381.20-3p

ASPE	American Society of Plumbing Engineers (ASPE) 6400 Shafer Ct, Ste 350, Rosemont Il 60018-4914 Phone: [phone] Website: www.aspe.org

Standard Reference Number

Title

1.

45-2018

Siphonic Roof Drainage

Section 58. SPS Tables 381.20-4, -5, -6, -7, -7e, -8, -9, -10, and -11 are repealed and recreated to read:

Table 381.20-4

ASSE/IAMPO

American Society of Sanitary Engineering 18927 Hickory Creek Drive, Suite 220 Mokena, Illinois 60448 Phone: [phone] Website: www.asse-plumbing.org

Standard Reference Number

Title

1.

1001-2017

Atmospheric Type Vacuum Breakers

2.

ASSE 1002-2020/ASME A112.1002-2020/CSA B125.12.20

Anti-siphon Fill Valves for Water Closet Tanks

3.

1003-2020 e1

Water Pressure Reducing Valves for Potable Water Distribution Systems

4.

1004-2017

Commercial Dishwashing Machines

5.

1008-­2020

Plumbing Aspects of Residential Food Waste Disposer Units

6.

1010-2004

Water Hammer Arresters

7.

1011-2017

Hose Connection Vacuum Breakers

8.

1012-2009

Backflow Preventer with Intermediate Atmospheric Vent

9.

1013-2011

Reduced Pressure Principle Backflow Preventers and Reduced Pressure Principle Fire Protection Backflow Preventers

10.

1014-2020

Backflow Prevention Devices for Hand-Held Showers

11.

1015-2011

Double Check Backflow Prevention Assemblies and Double Check Fire Protection Backflow Prevention Assemblies

12.

ASSE 1016-2017/ASME A112.1016-2017/CSA B125.16-17

Automatic Compensating Valves for Individual Showers and Tub/Shower Combinations

13.

1017-2009

Temperature Actuated Mixing Valves for Hot Water Distribution Systems

14.

1018-2001 (R2021)

Trap Seal Primer Valves - Potable Water Supplied

15.

1019-2011 (R2016)

Wall Hydrant with Backflow Protection and Freeze Resistance

16.

1020-2020 e1

Pressure Vacuum Breaker Assembly

17.

1022-2021

Backflow Preventer for Beverage Dispensing Equipment

18.

1023-2020

Hot Water Dispensers, Household Storage Type, Electrical

19.

1024-2017 (R2021)

Dual Check Backflow Preventers

20.

1032-2004 (R2021)

Dual Check Valve Type Backflow Preventers for Carbonated Beverage Dispensers, Post-Mix Type

21.

1035-2020

Laboratory Faucet Backflow Preventers

22.

1037-2015/ASME A112.1037-2015/CSA B125.37-15 (R2020)

Pressurized Flushing Devices for Plumbing Fixtures

23.

1044-2015

Trap Seal Primer – Drainage Types and Electric Design Types

24.

1047-2011

Reduced Pressure Detector Fire Protection Backflow Prevention Assemblies, Performance Requirements for

25.

1048-2011

Double Check Detector Fire Protection Backflow Prevention Assemblies, Performance Requirements for

26.

1049-2021

Performance Requirements for Individual and Branch Type Air Admittance Valves for Chemical Waste Systems

27.

1050-2021

Stack Air Admittance Valves for Sanitary Drainage Systems

28.

1051-2021

Individual and Branch Type Air Admittance Valves for Sanitary Drainage Systems

29.

1052-2016

Hose Connection Backflow Preventers, Performance Requirements for

30.

1053-2019

Dual Check Backflow Preventer Wall Hydrants - Freeze Resistant Type, Performance Requirements for

31.

ANSI/CAN/ASSE/ IAPMO 1055-2020

Chemical Dispensing Systems with Integral Backflow Protection, Performance Requirements for

32.

1056-2013 (R2021)

Spill Resistant Vacuum Breaker Assemblies, Performance Requirements for

33.

1057-2012

Freeze Resistant Sanitary Yard Hydrants with Backflow Protection, Performance Requirements for

34.

1061-2020

Performance Requirements for Push-Fit Fittings

35.

1066-1997

Individual Pressure Balancing In-Line Valves for Individual Fixture Fittings

36.

1072-2020

Performance Requirements for Barrier Type Trap Seal Protection for Floor Drains

37.

1079-2012 (R2021)

Performance Requirements for Dielectric Pipe Unions

38.

1081-2014 (R2020)

Performance Requirements for Backflow Preventers with Integral Pressure Reducing Boiler Feed Valve and Intermediate Atmospheric Vent Style for Domestic and Light Commercial Water Distribution Systems

39.

ASSE/IAPMO/ANSI SERIES 5000-2015

Cross Connection Control Professional Qualifications

40.

IAPMO/ANSI Z1001-2016

(Prefabricated Gravity Grease Interceptors)

Table 381.20-5

ASTM	ASTM International 100 Barr Harbor Drive West Conshohocken, Pennsylvania 19428-2959 Phone: [phone] Website: www.astm.org

Standard Reference Number

Title

1.

A53/A53M-20

Pipe, Steel, Black and Hot-Dipped, Zinc-Coated Welded and Seamless, Specification for

2.

A74-21

Cast Iron Soil Pipe and Fittings, Specification for

3.

A123/A123M-17

Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products, Standard Specification for

4.

A269/A269M Rev. A-15 (R2019)

Seamless and Welded Austenitic Stainless-Steel Tubing for General Service

5.

A270/A270M-15 (R2019)

Seamless and Welded Austenitic and Ferritic/Austenitic Stainless Steel Sanitary Tubing, Standard Specification for

6.

A312/A312M-2019

Seamless, Welded and Heavily Cold Worked Austenitic Stainless-Steel Pipes

7.

A358/A358M-2019

Electro-Fusion-Welded Austenitic Chromium-Nickel Stainless Steel Pipe for High-Temperature Service and General Applications

8.

A403/A403M-20

Wrought Austenitic Stainless Steel Piping Fittings, Standard Specification for

9.

A450/A450M-18a

Carbon, Ferritic Alloy, and Austenitic Alloy Steel Tubes

10.

A554-21

Welded Stainless Steel Mechanical Tubing

11.

A774/A774M-14 (R2019)

Welded Wrought Austenitic Stainless Steel Fittings for General Corrosive Service at Low and Moderate Temperatures

12.

A778/A778M-2016 (R2021)

Welded, Unannealed Austenitic Stainless Steel Tubular Products

13.

A888-21

Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Pipe Applications, Specifications for

14.

B32-20

Solder Metal,

15.

B42-20

Seamless Copper Pipe, Standard Sizes

16.

B43-20

Seamless Red Brass Pipe, Standard Sizes, Specification for

17.

B75/B75M-20

Standard Specification for Seamless Copper Tube

18.

B88-20

Seamless Copper Water Tube, Standard Specification for

19.

B88M-20

Seamless Copper Water Tube, (Metric), Standard Specification for

20.

B135/B135M-17

Standard Specification for Seamless Brass Tube

21.

B152/B152M-19

Copper Sheet, Strip, Plate, and Rolled Bar, Standard Specification for

22.

B251/B251M-17

Wrought Seamless Copper and Copper-Alloy Tube, Standard Specification for

23.

B302-17

Threadless Copper Pipe, Standard Sizes, Standard Specification for

24.

B306-20

Copper Drainage Tube (DWV), Standard Specification for

25.

B447-12a (R2021)

Standard Specification for Welded Copper Tube

26.

B828-16

Making Capillary Joints by Soldering of Copper and Copper Alloy Tube and Fittings, Standard Practice for

27.

C4-04 (R2018)

Clay Drain Tile and Perforated Clay Drain Tile

28.

C14-20

Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe, Specification for

29.

C14M-20

Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe (Metric), Specification for

30.

C33/C33M-18

Concrete Aggregates, Specification for

31.

C76-20

Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe, Specification for

32.

C76M-20

Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe, (Metric) Specifications for

33.

C163-17

Precast Concrete Grease Interceptor Tanks

34.

C425-04 (R2018)

Compression Joints for Vitrified Clay Pipe and Fittings, Standard Specification for

35.

C443-20

Joints for Circular Concrete Pipe and Manholes, Using Rubber Gaskets, Standard Specification for

36.

C443M-20

Joints for Circular Concrete Pipe and Manholes, Using Rubber Gaskets (Metric), Standard Specification for

37.

C507-20

Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe, Standard Specification for

38.

C507M-20

Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric)

39.

C564-20a

Rubber Gaskets for Cast Iron Soil Pipe and Fittings, Standard Specification for

40.

C700-18

Vitrified Clay Pipe, Extra Strength, Standard Strength, and Perforated, Standard Specification for

41.

C877-21

External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections, Standard Specifications for

42.

C877M-21

External Sealing Bands for Concrete Pipe, Manholes, and Precast Box Sections, (Metric)

43.

C887-20

Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar

44.

C923/C923M-20

Resilient Connectors Between Reinforced Concrete Manhole Structures, Pipes, and Laterals, Standard Specification for

45.

C990-09 (R2019)

Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants, Standard Specification for

46.

C990M-09 (R2019)

Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants (Metric)

47.

C1227-20

Precast Concrete Septic Tanks

48.

C1306/C1306M-08 (R2016)

Hydrostatic Pressure Resistance of a Liquid-Applied Waterproofing Membrane, Standard Test Method for

49.

C1478-20

Standard Specification for Storm Drain Resilient Connectors Between Reinforced Concrete Storm Sewer Structures, Pipes and Laterals

50.

C1628-19

Standard Specification for Joints for Concrete Gravity Flow Sewer Pipe Using Rubber Gaskets

51.

C1644-06 (R2017)

Standard Specification for Resilient Connectors Between Reinforced Concrete On-Site Wastewater Tanks and Pipes

52.

C1745/C1745M-18

Standard Test Method for Measurement of Hydraulic Characteristics of Hydrodynamic Stormwater Separators and Underground Settling Devices

53.

D1785-15

Poly (Vinyl Chloride) (PVC) Plastic Pipe, Schedules 40, 80, and 120, Standard Specification for

54.

D2235-04 (R2016)

Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings, Standard Specification for

55.

D2239-12a (R2020)

Polyethylene (PE) Plastic Pipe (SIDR-PR) Based on Controlled Inside Diameter, Standard Specification for

56.

D2241-20

Poly (Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR-Series), Standard Specification for

57.

D2321-20

Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications, Standard Practice for

58.

D2464-15

Threaded Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80, Standard Specification for

59.

D2466-17

Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 40, Standard Specification for

60.

D2467-20

Poly (Vinyl Chloride) (PVC) Plastic Pipe Fittings, Schedule 80, Standard Specification for

61.

D2564-20

Solvent Cements for Poly (Vinyl Chloride) (PVC) Plastic Systems, Standard Specification for

62.

D2609-15

Plastic Insert Fittings for Polyethylene (PE) Plastic Pipe, Standard Specification for

63.

D2657-07 (R2015)

Heat Fusion Joining of Polyolefin Pipe and Fittings, Standard Practice of

64.

D2661-14

Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings, Standard Specification for

65.

D2665-20

Poly (Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings, Standard Specification for

66.

D2680-20

Acrylonitrile-Butadiene-Styrene (ABS) and Poly (Vinyl Chloride) (PVC) Composite Sewer Piping, Specification for

67.

D2683-20

Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing, Standard Specification for

68.

D2729-17

Polyvinyl Chloride (PVC) Sewer Pipe and Fittings, Standard Specification for

69.

D2737-12a (R2020)

Polyethylene (PE) Plastic Tubing, Standard Specification for

70.

D2774-21

Underground Installation of Thermoplastic Pressure Piping, Standard Practice for

71.

D2846/D2846M-19a

Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems, Standard Specification for

72.

D2852-16

Styrene-Rubber (SR) Plastic Drain Pipe and Fittings, Standard Specification for

73.

D2855-20

Making Solvent-Cemented Joints with Poly (Vinyl Chloride) (PVC) Pipe and Fittings, Standard Practice for

74.

D3034-16

Type PSM Poly (Vinyl Chloride) (PVC) Sewer Pipe and Fittings, Standard Specification for

75.

D3035-15

Polyethylene (PE) Plastic Pipe (SDR-PR) Based on Controlled Outside Diameter, Standard Specification for

76.

D3138-04 (R2016)

Solvent Cements for Transition Joints Between Acrylonitrile-Butadiene-Styrene (ABS) and Poly (Vinyl Chloride) (PVC) Non-Pressure Piping Components, Standard Specification for

77.

D3212-20

Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals, Standard Specification for

78.

D3261-16

Butt Heat Fusion Polyethylene (PE) Plastic Fittings for Polyethylene (PE) Plastic Pipe and Tubing, Standard Specification for

79.

D3311-17

Drain, Waste, and Vent (DWV) Plastic Fittings Patterns, Standard Specification for

80.

D4068-17

Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane

81.

D4491/D4491M-20

Water Permeability of Geotextile by Permittivity, Standard Specification for

82.

D4533/D4533M-15

Trapezoid Tearing Strength of Geotextiles, Standard Test Method for

83.

D4632/D4632M-15a

Grab Breaking Load and Elongation of Geotextiles, Standard Test Method for

84.

D4751-20b

Determining Apparent Opening Size of a Geotextile, Standard Test Method for

85.

D4833/D4833M-07 (R2020)

Index Puncture Resistance of Geomembranes, and Related Products, Standard Test Method for

86.

F402-18

Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings, Standard Practice for

87.

F409-17

Thermoplastic Accessible and Replaceable Plastic Tube and Tubular Fittings, Standard Specification for

88.

F437-15

Threaded Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80, Standard Specification for

89.

F438-17

Socket-Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 40, Standard Specification for

90.

F439-19

Socket-Type Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe Fittings, Schedule 80, Standard Specification for

91.

F441/F441M-20

Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe, Schedules 40 and 80, Standard Specification for

92.

F442/F442M-20

Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe (SDR-PR), Standard Specification for

93.

F477-14

Elastomeric Seals (Gaskets) for Joining Plastic Pipe, Standard Specification for

94.

F481-97 (R2019)

Standard Practice for Installation of Thermoplastic Pipe and Corrugated Pipe in Septic Tank Leach Fields

95.

F493-20

Solvent Cements for Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic Pipe and Fittings, Standard Specification for

96.

F585-16 (R2021)

Standard Guide for Insertion of Flexible PE Pipe into Existing Sewers

97.

F628-12

Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe with a Cellular Core, Standard Specification for

98.

F656-15

Primers for Use in Solvent Cement Joints of Poly (Vinyl Chloride) (PVC) Plastic Pipe and Fittings, Standard Specification for

99.

F667/F667M-16

3 through 24 in. Corrugated Polyethylene Pipe and Fittings, Standard Specification for

100.

F679-16

Poly (Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings, Standard Specification for

101.

F714-21a

Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter

102.

F794-03 (R2014)

Poly (Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter, Standard Specification for

103.

F810-12 (R2018)

Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields, Standard Specification for

104.

F876-20b

Crosslinked Polyethylene (PEX) Tubing, Standard Specification for

105.

F877-20

Crosslinked Polyethylene (PEX) Plastic Hot- and Cold-Water Distribution Systems, Standard Specification for

106.

F891-16

Coextruded Poly (Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core, Standard Specification for

107.

F894-19

PE Large Diameter Profile Wall Sewer and Drain Pipe

108.

F949-20

Poly (Vinyl Chloride) (PVC) Corrugated Sewer Pipe With a Smooth Interior and Fittings, Standard Specification for

109.

F1055-16a

Standard Specification for Electrofusion Type Polyethylene Fittings for Outside Diameter Controlled Polyethylene and PEX Pipe and Tubing

110.

F1281-17

Crosslinked Polyethylene/Aluminum/Crosslinked Polyethylene (PEX-AL-PEX) Pressure Pipe, Standard Specification for

111.

F1282-17

Polyethylene/Aluminum/Polyethylene (PE-AL-PE) Composite Pressure Pipe, Standard Specification for

112.

F1336-20

Poly (Vinyl Chloride) (PVC) Gasketed Sewer Fittings, Specification for

113.

F1412-16

Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems

114.

F1673-10 (R2016)

Standard Specification for Polyvinylidene Fluoride (PVDF) Waste Drainage Systems

115.

F1732-12 (R2018)

Standard Specification for PVC Sewer and Drain Pipe Containing Recycled PVC Material

116.

F1760-16 (R2020)

Standard Specification for Coextruded PVC Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content

117.

F1807-19b

Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing, Standard Specification for

118.

F1866-18

Poly (Vinyl Chloride) (PVC) Plastic Schedule 40 Drainage and DWV Fabricated Fittings, Specifications for

119.

F1901-16

Standard Specification for PE Pipe and Fittings for Roof Drain Systems

120.

F1960-21

Standard Specification for Cold Expansion Fittings with PEX Reinforcing Rings for Use with Cross-linked Polyethylene (PEX) and Polyethylene of Raised Temperature (PE-RT) Tubing

121.

F1962-20

Standard Guide for Use of Maxim-Horizontal Directional Drilling for Placement of Polyethylene Pipe or Conduit Under Obstacles, Including River Crossings

122.

F1970-19

Standard Specification for Special Engineered Fittings, Appurtenances or Valves for use in Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Systems

123.

F1974-09 (R2020)

Standard Specification for Metal Insert Fittings for PE-AL-PE and Crosslinked PEX-AL-PEX Composite Pressure Pipe

124.

F2021-17

Design & Installation of Plastic Siphonic Roof Drain Systems

125.

F2080-19

Standard Specification for Cold-Expansion Fittings with Metal Compression-Sleeves for Crosslinked Polyethylene (PEX) Pipe and SDR9 Polyethylene of Raised Temperature (PE-RT) Pipe

126.

F2098-18

Standard Specification for Stainless Steel Clamps for Securing SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) to Metal Insert and Plastic Insert Fittings

127.

F2159-21

Standard Specification for Plastic Insert Fittings Utilizing a Copper Crimp Ring, or Alternate Stainless Steel Clamps for SDR9 Crosslinked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

128.

F2165-19

Standard Specification for Flexible Pre-Insulated Plastic Piping

129.

F2389-21

Standard Specification for Pressure Rated Polypropylene (PP) Piping Systems

130.

F2390-21

Standard Specification for PVC Plastic Drain, Waste and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content

131.

F2418-19

Standard Specification for Polypropylene (PP) Corrugated Wall Stormwater Collection Chambers

132.

F2434-19

Standard Specification for Metal Insert Fittings Utilizing a Copper Crimp Ring for SDR9 PEX and SDR9 PEX-AL-PEX Tubing

133.

F2510/2510M-17

Standard Specification for Resilient Connectors Between Reinforced Concrete Manhole Structures and Corrugated Dual- and Triple-Wall PE and PP Pipes

134.

F2618-21

Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Drainage Systems

135.

F2620-20

Standard Practice for Heat Fusion Joining of Polyethylene Pipe and Fittings

136.

F2649-14 (R2019)

Standard Specification for Corrugated HDPE Grease Interceptor Tanks

137.

F2735-21

Standard Specification for Plastic Insert Fittings for SDR9 PEX and PE-RT Tubing

138.

F2737-11 (R2021)

Standard Specification for Corrugated HDPE Water Quality Units

139.

F2763/F2763M-16 (R2021)

Standard Specification for 12 to 60 in. Dual- and Triple Profile Wall PE Pipe and Fittings for Sanitary Sewer Applications

140.

F2764/F2764M-19

Standard Specification for 6 to 60 in. PP Corrugated Double- and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications

141.

F2769-18

Standard Specification for Polyethylene of Raised Temperature (PE_RT) Plastic Hot and Cold-Water Tubing and Distribution Systems

142.

F2787-13 (R2018)

Standard Practice for Structural Design of Thermoplastic Corrugated Wall Stormwater Collection Chambers)

143.

F2829/F2829M-21

Standard Specification for Metric- and Inch-Sized Fittings for PEX Pipe

144.

F2854-21

Standard Specification for Push-Fit PEX Mechanical Fittings for PEX Tubing

145.

F2855-19

Standard Specification for CPVC-AL-CPVC Composite Pressure Tubing

146.

F2881/2881M-21

Standard Specification for 12 to 60 in. PP Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications

147.

F2922-13 (R2018)

Standard Specification for Polyethylene (PE) Corrugated Stormwater Collection Chambers

148.

F3190-21

Standard Practice for Heat Fusion Equipment (HFE) Operator Qualification on PE and Polyamide Pipe and Fittings

149.

F3328-18

Standard Practice for the One-Step (Solvent Cement Only) Method of Joining Poly (Vinyl Chloride) (PVC) or Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Piping Components with Tapered Sockets

150.

F3346-19

Standard Specification for PE-RT-AL-PE-RT Composite Pressure Pipe

151.

F3347-20a

Standard Specification for Metal Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

152.

F3348-21

Standard Specification for Plastic Press Insert Fittings with Factory Assembled Stainless Steel Press Sleeve for SDR9 Cross-linked Polyethylene (PEX) Tubing and SDR9 Polyethylene of Raised Temperature (PE-RT) Tubing

Table 381.20-6

AWS	American Welding Society 8669 NW 36 Street, #130 Miami, Florida 33166-6672 Phone: [phone] Website: www.aws.org

Standard Reference Number

Title

1.

AWS A5.8M/A5.8:2019

Filler Metals for Brazing and Braze Welding, Specification for

Table 381.20-7

AWW 904-16

American Water Works Association (AWWA) 6666 West Quincy Avenue Denver, Colorado 80235 Phone: [phone] or 800-926-7337 Website: www.awwa.org

Standard Reference Number

Title

1.

ANSI/AWWA C110/A21.10-12

American National Standard for Ductile-Iron and Gray-Iron Fittings

2.

ANSI/AWWA C111/A21.11-17

American National Standard for Rubber-Gasket Joints for Ductile-Iron Pressure Pipe and Fittings

3.

ANSI/AWWA C115/A21.15-20

American National Standard for Flanged Ductile-Iron Pipe with Ductile-Type Iron or Gray-Iron Pipe Threaded Flanges

4.

ANSI/AWWA C151/A21.51-17

Ductile-Iron Pipe, Centrifugally Cast, for Water

5.

ANSI/AWWA C153/A21.53-19

American National Standard for Ductile-Iron Compact Fittings, 3 in. through 16 in., for Water and Other Liquids

6.

ANSI/AWWA C220-17

Stainless–Steel Pipe, ½ in. (13mm) and Larger

7.

ANSI/AWWA C651-14

Water Mains, Disinfecting

8.

ANSI/AWWA C700-20

Cold-Water Meters — Displacement Type with Bronze Metal Main Case (w/ 1991 Addendum)

9.

ANSI/AWWA C701-15

Cold-Water Meters — Turbine Type, for Customer Service

10.

ANSI/AWWA C702-19

Cold-Water Meters — Compound Type

11.

ANSI/AWWA C704-19

Cold-Water Meters — Propeller Type for Main Line Applications

12.

ANSI/AWWA C707-10 (R2016)

Cold-Water Meters, Encoder-Type, Remote-Registration Systems

13.

ANSI/AWWA C708-19

Cold-Water Meters — Multi-Jet Type

14.

ANSI/AWWA C710-20

Cold-Water Meters, Displacement Type — Plastic Main

15.

ANSI/AWWA C900-16

Polyvinyl Chloride (PVC) Pressure Pipe and Fabricated Fittings 4-inch to 12-inch (100mm Through 300 mm) for Water Transmission and Distribution

16.

ANSI/AWWA C901-20

Polyethylene (PE) Pressure Pipe and Tubing, 1/2 in. (13mm) Through 3 in. (76mm) for Water Service

17.

ANSI/AWWA C904-16

Cross-Linked PEX Pressure Tubing ½-3 in. for Water Service

18.

ANSI/AWWA C906-15

Polyethylene Pressure Pipe and Fittings, 4 in. through 63 in., for Water Distribution

Table 381.20-7e

CSA	Canadian Standards Association 178 Rexdale Boulevard Toronto, Ontario Canada M9W 1R3 Phone: [phone] Website: www.csagroup.org

Standard Reference Number

Title

1.

4.1:19/Z21.10.1:19

Gas water heaters, volume I, storage water heaters with input ratings of 75,000 Btu per hour or less

2.

4.3:19/Z21.10.3:19

Gas-fired water heaters, volume III, storage water heaters with input ratings above 75,000 Btu per hour, circulating and instantaneous

3.

4.4-2015 (R2020) / ANSI Z21.22-2015 (R2020)

Relief Valves for Hot Water Supply Systems

4.

B45.5-17/IAPMO Z124-2017

Vacuum Waste Collection Systems

5.

B45.13:19/IAPMO Z1700-2019

Vacuum Waste Collection Systems

6.

B64 SERIES-11 (R2016)

Backflow preventers and vacuum breakers

7.

B66-16

Design, Material and Manufacturing Requirements for Prefabricated Septic Tanks and Sewage Holding Tanks

8.

B125.3–18

Plumbing Fittings

9.

B137:20

Thermoplastic Pressure Piping Standards Package - Consists of All The CSA B137:20 Standards

10.

B481 Series 12 (R2017)

Grease Interceptors

11.

B1800:21

Thermoplastic Non-pressure Piping Compendium (Numbers 17 and 18 are superseded by CSA B1800.)

Table 381.20-8

CISPI

Cast Iron Soil Pipe Institute 2401 Fieldcrest Dr. Mundelein, IL 60060 Phone: [phone] Website: www.cispi.org

Standard Reference Number

Title

1.

301-18

Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications, Standard Specification for

2.

310-20

Coupling for Use in Connection with Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications, Specification for

Table 381.20-9

FMRC	FM Global (FMRC) 270 Central Avenue Johnston, RI 02919-4949 Phone: [phone] Website: www.fmglobal.com

Standard Reference Number

Title

1.

1680-89

Couplings Used in Hubless Cast Iron Systems for Drain, Waste or Vent, Sewer, Rainwater or Storm Drain Systems Above and Below Ground, Industrial/Commercial and Residential, January 1989

Table 381.20-10

NFPA

National Fire Protection Association 1 Batterymarch Park Quincy, MA 02169-7471 Phone: [phone] Website: www.nfpa.org

Standard Reference Number

Title

1.

NFPA 13D-2019

Installation of Sprinkler Systems in One- and Two-Family Dwellings and Manufactured Homes, Standard for the

2.

NFPA 24-2019

Installation of Private Fire Service Mains and Their Appurtenances, Standard for the

Table 381.20-11

NSF	NSF International (NSF) 789 N. Dixboro Road P.O. Box 130140 Ann Arbor, Michigan 48105 Phone: [phone] Website: www.nsf.org

Standard Reference Number

Title

1.

NSF/ANSI 3-2019

Commercial Warewashing Equipment

2.

NSF/ANSI 12-2018

Automatic Ice Making Equipment

3.

P157-2000

Electrical Incinerating Toilets – Health and Sanitization

4.

NSF/ANSI 14-2020

Plastic Piping System Components and Related Materials

5.

NSF/ANSI 40-2019

Residential Wastewater Treatment Systems

6.

NSF/ANSI 41-2018

Non-liquid Saturated Treatment Systems

7.

NSF/ANSI 42-2020

Drinking Water Treatment Units – Aesthetic Effects

8.

NSF/ANSI 44-2018

Residential Cation Exchange Water Softeners

9.

NSF/ANSI 46-2021

Evaluation of Components and Devices Used in Wastewater Treatment Systems

10.

NSF/ANSI/CAN 50-2019

Equipment and Chemicals for Swimming Pools, Spas, Hot Tubs, and Other Recreational Water Facilities

11.

NSF/ANSI 51-2019

Food Equipment Materials

12.

NSF/ANSI 53-2020

Drinking Water Treatment Units – Health Effects

13.

NSF/ANSI 55-2019

Ultraviolet Microbiological Water Treatment Systems

14.

NSF/ANSI 58-2020

Reverse Osmosis Drinking Water Systems

15.

NSF/ANSI/CAN 60-2020

Drinking Water Treatment Chemicals – Health Effects

16.

NSF/ANSI/CAN 61-2020

Drinking Water System Components — Health Effects

17.

NSF/ANSI 62-2020

Drinking Water Distillation Systems

18.

NSF/ANSI 184-2019

Residential Dishwashers

19.

NSF/ANSI 240-2017

Drainfield Trench Product Sizing for Gravity Dispersal Onsite Wastewater Treatment and Dispersal Systems

20.

NSF/ANSI 245-2019

Residential Wastewater Treatment Systems - Nitrogen Reduction

21.

NSF/ANSI 350-2020

Onsite Residential and Commercial Water Reuse Treatment Systems

22.

NSF/ANSI 350-1-2017

Onsite Residential and Commercial Greywater Treatment Systems for Subsurface Discharge

23.

NSF/ANSI 359-2018

Valves for PEX Water Distribution Tubing Systems

24.

NSF/ANSI 372-2020

Drinking Water System Components — Lead Content

Section 59. SPS Table 381.20-11m is created to read:

Table 381.20-11m

PDI	The Plumbing and Drainage Institute (PDI) 800-589-8956 Website: www.pdionline.org

Standard Reference Number

Title

1.

PDI-G 101 (R2017)

Testing and Rating Procedure for Hydro Mechanical Grease Interceptors with Appendix of Installation and Maintenance

2.

PDI-G 102 (2009)

Testing and Certification for Grease Interceptors with FOG Sensing and Alarm Devices

Section 60. SPS Table 381.20-12 and –13 are amended to read:

Table 381.20-12

STI/SPFA

Steel Tank Institute/Steel Plate Fabricators Association 570 Oakwood Road 944 Donata Court Lake Zurich, Illinois 60047 Phone: [phone] Web page Website: www.steeltank.com

Standard Reference Number

Title

1.

STI-P3 STI/SPFA STI-P3-2018

External Corrosion Protection of Underground Steel Storage Tanks, Specifications and Manual for