(b) “Contact adhesive” does not include any of the following:
1. Rubber cements that are primarily intended for use on paper substrates.
2. Vulcanizing fluids that are designed and labeled for tire repair only.
(19v) “Cove base” means a flooring trim unit, generally made of vinyl or rubber, that has a concave radius on one edge and a convex radius on the opposite edge that is used in forming a junction between the bottom wall course and the floor or to form an inside corner.
(19x) “Cove base installation adhesive” means any adhesive intended by the manufacturer to be used for the installation of cove base or wall base on a wall or vertical surface at floor level.
(20q) “Cyanoacrylate adhesive” means any adhesive with a cyanoacrylate content of at least 95 percent by weight.
(20u) “Dip coating” means a method of applying coatings in which the part to be coated is submerged in a tank filled with the coating.
(20y) “Drum” means any cylindrical metal shipping container larger than 12 gallons capacity but no larger than 110 gallons capacity.
(21d) “Electric dissipating coating” means a coating that rapidly dissipates a high voltage electric charge.
(21j) “Electric-insulating varnish” means a non-convertible-type coating applied to electric motors, components of electric motors, or power transformers, to provide electrical, mechanical, and environmental protection or resistance.
(25g) “EPDM roof membrane” means a prefabricated single sheet of elastomeric material composed of ethylene propylene diene monomer and that is field applied to a building roof using one layer or membrane material.
(25r) “Etching filler” means a coating that contains less than 23 percent solids by weight and at least 0.5 percent acid by weight and is used instead of applying a pretreatment coating followed by a primer.
(32m) “Finish primer surfacer” means a coating applied with a wet film thickness of less than 10 mils prior to the application of a topcoat for purposes of providing corrosion resistance, adhesion of subsequent coatings, a moisture barrier, or promotion of a uniform surface necessary for filling in surface imperfections.
(34d) “Flexible coating” means a coating that is required to comply with engineering specifications for impact resistance, mandrel bend, or elongation, as those terms are defined by the original equipment manufacturer.
(34v) “Flexible vinyl” means non-rigid polyvinyl chloride plastic with a 5 percent by weight plasticizer content.
(36m) “Fog coat” means a coating that is applied to a plastic part for the purpose of color matching without masking a molded-in texture and that is not applied at a thickness of more than 0.5 mils of coating solids.
(38m) “Gloss reducer” means a coating that is applied to a plastic part solely to reduce the shine of the part and that is not applied at a thickness of more than 0.5 mils of coating solids.
(41e) “High bake” means a coating that is designed to cure only at temperatures of more than 194°F.
(41m) “High build primer surfacer” means a coating applied with a wet film thickness of 10 mils or more prior to the application of a topcoat for any of the following purposes:
(a) Providing corrosion resistance.
(b) Providing adhesion of subsequent coatings.
(c) Providing a moisture barrier.
(d) Promoting a uniform surface necessary for filling in surface imperfections.
(41s) “High gloss coating” means a coating that achieves at least 85 percent reflectance on a 60° glossmeter when tested by ASTM D 523-89, incorporated by reference under s. NR 484.10 (9). (42d) “High temperature coating” means a coating that is certified to withstand a temperature of 1000°F for 24 hours.
(42h) “High-volume, low-pressure spray” means equipment used to apply coatings by means of a spray gun that operates between 0.1 and 10 psig air pressure.
Note: High-volume, low-pressure is also referred to as HVLP.
(42s) (a) “Indoor floor covering installation adhesive” means any adhesive intended by the manufacturer for use in the installation of wood flooring, carpet, resilient tile, vinyl tile, vinyl backed carpet, resilient sheet and roll, or artificial grass.
(b) “Indoor floor covering installation adhesive” does not include an adhesive used to install ceramic tile and perimeter bonded sheet flooring with vinyl backing onto a non-porous substrate, such as flexible vinyl.
(45s) “Laminate” means a product made by bonding together 2 or more layers of material.
(53j) “Metal to urethane/rubber molding or casting adhesive” means any adhesive intended by the manufacturer to bond metal to high density or elastomeric urethane or molded rubber materials, in heater molding or casting processes, to fabricate products such as rollers for computer printers or other paper handling equipment.
(53k) “Military specification coating” means a coating that has a formulation approved by a United States military agency for use on military equipment.
(54a) “Mold seal coating” means the initial coating applied to a new mold or a repaired mold to provide a smooth surface that, when coated with a mold release coating, prevents products from sticking to the mold.
(54b) “Motor vehicle adhesive” means an adhesive, including glass bonding adhesive, used at a facility that is not an automobile or light-duty truck assembly coating facility, applied for the purpose of bonding 2 vehicle surfaces together without regard to the substrates involved.
(54c) “Motor vehicle bedliner” means a multi-component coating, used at a facility that is not an automobile or light-duty truck assembly coating facility, applied to a cargo bed after the application of topcoat to provide additional durability and chip resistance.
(54d) “Motor vehicle cavity wax” means a coating, used at a facility that is not an automobile or light-duty truck assembly coating facility, applied into the cavities of a vehicle primarily for the purpose of enhancing corrosion protection.
(54e) “Motor vehicle deadener” means a coating, used at a facility that is not an automobile or light-duty truck assembly coating facility, applied to selected vehicle surfaces primarily for the purpose of reducing the sound of road noise in the passenger compartment.
(54f) (a) “Motor vehicle gasket/gasket sealing material” means a fluid, used at a facility that is not an automobile or light-duty truck assembly coating facility, applied to coat a gasket or replace and perform the same function as a gasket.
(b) “Motor vehicle gasket/gasket sealing material” includes room temperature vulcanization seal material.
Note: Room temperature vulcanization is also referred to as RTV.
(54g) (a) “Motor vehicle glass bonding primer” means a primer, used at a facility that is not an automobile or light-duty truck assembly coating facility, applied to windshield or other glass, or to body openings, to prepare the glass or body opening for the application of glass bonding adhesives or the installation of adhesive bonded glass.
(b) “Motor vehicle glass bonding primer” includes a glass bonding or cleaning primer that cleans and primes a windshield or other glass, or body openings, prior to the application of adhesive or the installation of adhesive bonded glass.
(54h) “Motor vehicle lubricating wax/compound” means a protective lubricating material, used at a facility that is not an automobile or light-duty truck assembly coating facility, applied to vehicle hubs and hinges.
(54i) “Motor vehicle sealer” means a high viscosity material, used at a facility that is not an automobile or light-duty truck assembly coating facility, generally applied in a paint shop after the body has received an electrodeposition primer coating and before the application of subsequent coatings, such as primer-surfacer, that has a primary purpose of filling body joints completely so that there is no intrusion of water, gases, or corrosive materials into the passenger area of the body compartment.
Note: Motor vehicle sealers are also referred to as sealants, sealant primers, or caulks.
(54j) “Motor vehicle trunk interior coating” means a coating, used at a facility that is not an automobile or light-duty truck assembly coating facility, applied to the trunk interior to provide chip protection.
(54k) “Motor vehicle underbody coating” means a coating, used at a facility that is not an automobile or light-duty truck assembly coating facility, applied to the undercarriage or firewall to prevent corrosion or provide chip protection, or both.
(54L) “Motor vehicle weatherstrip adhesive” means an adhesive, used at a facility that is not an automobile or light-duty truck assembly coating facility, applied to weatherstripping materials for the purpose of bonding the weatherstrip material to the surface of the vehicle.
Section 8 NR 422.02 (54m) is renumbered (54p).
Section 9 NR 422.02 (54o), (54y) and (Note), (57s), (58m), (61s), (63m), (64g), (64q), (64u), (65e), (65m), (65s), (66m), (74m) and (Note), (75m), (80f) and (Note), (86e), (86m), (86s), (87d), (87h), (87L), (93m), (95s), (100m), (104m), (106s), and (109s) are created to read:
NR 422.02 (54o) “Multi-colored coating” means a coating that exhibits more than one color when applied and that is packaged in a single container and applied in a single coat.
(54y) “Multipurpose construction adhesive” means an adhesive intended by the manufacturer for use in the installation or repair of various construction materials, including drywall, subfloor, panel, fiberglass reinforced plastic, ceiling tile, and acoustical tile.
Note: Fiberglass reinforced plastic is also referred to as FRP.
(57s) “Optical coating” means a coating applied to an optical lens.
(58m) “Outdoor floor covering installation adhesive” means an adhesive intended by the manufacturer for use in the installation of floor covering that is not in an enclosure and that is exposed to ambient weather conditions during normal use.
(61s) “Pan-backing coating” means a coating applied to the surface of pots, pans, or other cooking implements that are exposed directly to a flame or other heating elements.
(63m) “Perimeter bonded sheet vinyl floor covering installation” means the installation of sheet flooring with vinyl backing onto a nonporous substrate using an adhesive designed to be applied only to a strip of up to 4 inches wide around the perimeter of the sheet flooring.
(64g) “Plastic” means a synthetic material chemically formed by the polymerization of carbon-based substances that is usually compounded with modifiers, extenders, or reinforcers and is capable of being molded, extruded, cast into various shapes and films, or drawn into filaments.
(64q) “Plastic solvent welding adhesive” means an adhesive intended by the manufacturer for use to dissolve the surface of plastic to form a bond between mating surfaces.
(64u) “Plastic solvent welding adhesive primer” means a primer intended by the manufacturer for use to prepare plastic substrates prior to bonding or welding.
(65e) “Pleasure craft” is a vessel that is manufactured or operated primarily for recreational purposes, or leased, rented, or chartered to a person or business for recreational purposes.
(65m) “Pleasure craft coating” means a marine coating, except unsaturated polyester resin or fiberglass coatings, applied by brush, spray, roller, or other means to a pleasure craft.
(65s) (a) “Porous material” means a substance that has tiny openings, often microscopic, in which fluids may be absorbed or discharged, including paper and corrugated paperboard.
(b) “Porous material” does not include wood.
(66m) “Prefabricated architectural component coating” means a coating applied to metal parts and products that are to be used as part of an architectural structure.
(74m) “Red coating” means a coating that meets all of the following criteria:
(a) Yellow limit: the hue of hostaperm scarlet.
(b) Blue limit: the hue of monastral red-violet.
(c) Lightness limit for metallics: 35 percent aluminum flake.
(d) Lightness limit for solids: 50 percent titanium dioxide white.
(e) Solid reds: hue angle of -11 to 38 degrees and maximum lightness of 23 to 45 units.
(f) Metallic reds: hue angle of -16 to 35 degrees and maximum lightness of 28 to 45 units.
Note: The criteria under this subsection are based on Cielab color space, 0/45 geometry. For spherical geometry, specular included, the upper limit is 49 units. The maximum lightness varies as the hue moves from violet to orange. This is a natural consequence of the strength of the colorants, and real colors show this effect.
(75m) “Reinforced plastic composite” means a composite material consisting of plastic reinforced with fibers.
(80f) “Rubber” means any natural or manmade rubber substrate, including styrene-butadiene rubber, polychloroprene, butyl rubber, nitrile rubber, chlorosulfonated polyethylene, and ethylene propylene diene terpolymer.
Note: Polychloroprene is also referred to as neoprene.
(86e) (a) “Sheet rubber lining installation” means the process of applying sheet rubber liners by hand to metal or plastic substrates to protect the underlying substrate from corrosion or abrasion.
(b) “Sheet rubber lining installation” includes laminating sheet rubber to fabric by hand.
(86m) “Shock-free coating” means a coating applied to electrical components to protect the user from electric shock that has characteristics of being of low capacitance and high resistance and is resistant to breaking down under high voltage.
(86s) “Silicone release coating” means a coating that contains silicone resin and is intended to prevent food from sticking to metal surfaces, such as baking pans.
(87d) (a) “Single-ply roof membrane” means a prefabricated single sheet of rubber, normally ethylene propylene diene terpolymer, that is field applied to a building roof using one layer of membrane material.
(b) “Single-ply roof membrane” does not include a membrane prefabricated from ethylene propylene diene monomer.
(87h) “Single-ply roof membrane adhesive primer” means a primer labeled for use to clean and promote adhesion of single-ply roof membrane seams or splices prior to bonding.
(87L) (a) “Single-ply roof membrane installation and repair adhesive” means an adhesive labeled for use in the installation or repair of single-ply roof membrane.
(b) In this subsection:
1. “Installation” includes, as a minimum, attaching the edge of the membrane to the edge of the roof and applying flashings to vents, pipes, and ducts that protrude through the membrane.
2. “Repair” includes gluing the edges of torn membrane together, attaching a patch over a hole, and reapplying flashings to vents, pipes, or ducts installed through the membrane.
